|
IEC 63103
Edition 1.0 2020-07
INTERNATIONAL
STANDARD
colour
inside
Lighting equipment – Non-active mode power measurement
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de
CH-1211 Geneva 20
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.
need further assistance, please contact the Customer Service
.
IEC 63103
Edition 1.0 2020-07
INTERNATIONAL
STANDARD
colour
inside
Lighting equipment – Non-active mode power measurement
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.140.01; 29.140.99 ISBN 978-2-8322-8648-7
– 2 – IEC 63103:2020 © IEC 2020
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 General test conditions . 11
4.1 General . 11
4.2 Laboratory and environmental conditions . 11
4.3 Supply voltage . 11
4.3.1 Supply voltage and frequency . 11
4.3.2 Supply voltage waveform . 11
4.4 Power measurement accuracy and uncertainty . 11
4.5 Network aspects . 12
4.5.1 General . 12
4.5.2 Wired networks . 12
4.5.3 Wireless networks: conducted connection for testing . 12
4.5.4 Wireless networks: radiated connection for testing. 13
5 Measurements . 15
5.1 General . 15
5.2 Equipment under test (EUT) . 15
5.2.1 General . 15
5.2.2 Illumination-only lighting equipment . 15
5.2.3 Multi-function lighting equipment . 19
5.3 Preparation of EUT . 20
5.3.1 General . 20
5.3.2 Measurement of input power . 20
5.3.3 EUT with no network provision . 22
5.3.4 EUT with network provision (wired or wireless) . 22
5.4 Measuring procedure . 22
5.4.1 General . 22
5.4.2 Direct meter reading method . 23
5.4.3 Average reading method . 23
5.4.4 Sampling method . 24
Annex A (informative) Guidance for product standards . 26
Annex B (normative) Measurement setup schemes for illumination-only lighting
equipment . 27
Annex C (normative) Measurement setup schemes for multi-function lighting
equipment . 30
........................................................................ 31
.......................................................................................................................... 33
Figure 1 – Test setup for non-active mode power consumption measurement of
conducted connected EUT . 13
Figure 2 – Test setup for non-active mode power consumption measurement of
connected EUT with integral antennas (RF path symbolically shown) . 14
Figure 3 – Calibration setup for non-active mode power measurement of connected
EUT with integral antennas . 14
Figure 4 – Components present within illumination-only EUT . 15
Figure 5 – Component representing an additional function (AF) of multi-function EUT . 19
Figure 6 – Configuration of multi-function lighting equipment: example including one
additional function . 19
Figure B.1 – Key to symbols used in figures of Annex B. 27
Figure B.2 – Measurement setup for determining the input power supplied to the power
supply . 27
Figure B.3 – Measurement setup (with optional network provision) for determining the
input power supplied to the control unit . 28
Figure B.4 – Measurement setup (with optional network provision) for determining the
input power supplied to the combined power supply and control unit . 28
Figure B.5 – Measurement setup for determining the input power supplied to the
combined light source and power supply . 28
Figure B.6 – Measurement setup (with optional network provision) for determining the
input power supplied to the combined light source and control unit . 28
Figure B.7 – Measurement setup (with optional network provision) for determining the
input power supplied to illumination-only lighting equipment . 29
Figure C.1 – Key to symbols used in figures of Annex C . 30
Figure C.2 – Measurement setup (with optional network provision) for determining the
input power to multi-function lighting equipment . 30
Figure D.1 – General measurement setup scheme for controlgear examples . 31
Figure D.2 – Networked standby mode measurement setup for the "basic" controlgear . 32
Figure D.3 – Networked standby mode measurement setup for controlgear with an
integrated auxiliary/bus power supply function . 32
Table 1 – Configurations and examples of illumination-only equipment and reference to
the measurement setup . 17
Table 2 – Template for reporting non-active mode power . 18
Table 3 – Example of using the template of Table 2 for reporting measured standby
power for an illumination-only luminaire with integrated presence sensor . 18
Table 4 – Example of using the template of Table 2 for reporting measured standby
power for a (multi-function) luminaire with an integrated presence sensor and an
integrated camera . 20
– 4 – IEC 63103:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LIGHTING EQUIPMENT –
NON-ACTIVE MODE POWER MEASUREMENT
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses aris
...