|
IEC TS 62607-6-14
Edition 1.0 2020-10
TECHNICAL
SPECIFICATION
colour
inside
Nanomanufacturing – Key control characteristics –
Part 6-14: Graphene-based material – Defect level: Raman spectroscopy
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de
CH-1211 Geneva 20
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.
need further assistance, please contact the Customer Service
.
IEC TS 62607-6-14
Edition 1.0 2020-10
TECHNICAL
SPECIFICATION
colour
inside
Nanomanufacturing – Key control characteristics –
Part 6-14: Graphene-based material – Defect level: Raman spectroscopy
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 07.120 ISBN 978-2-8322-8940-2
– 2 – IEC TS 62607-6-14:2020 IEC:2020
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
3.1 General terms . 8
3.2 Key control characteristics measured in accordance with this document . 11
4 General . 11
4.1 Measurement principle . 11
4.2 Sample preparation method . 12
4.3 Description of measurement equipment/apparatus . 12
4.4 Supporting materials . 12
4.5 Ambient conditions during measurement . 12
5 Measurement procedure . 13
5.1 Calibration of measurement equipment . 13
5.2 Detailed protocol of the measurement procedure . 13
5.3 Measurement accuracy . 13
5.4 Measurement uncertainty source . 13
6 Sampling plan . 13
7 Data analysis / interpretation of results . 13
8 Results to be reported . 14
8.1 General . 14
8.2 Product/sample identification . 14
8.3 Test conditions . 14
8.4 Measurement specific information . 14
8.5 Test results . 14
Annex A (informative) Recommended format of the test report . 15
Annex B (informative) Sampling plan . 17
Annex C (informative) Case study: measurement and data analysis . 18
C.1 Step 1: sample preparation . 18
C.2 Step 2: Raman test . 18
C.3 Step 3: Raman spectra processing . 18
C.4 Step 4: Data analysis . 19
Annex D (informative) Why use the intensity ratio I /I for defect level
D+D′ 2D
characterization of graphene powder? . 22
D.1 Interpretation of characteristic bands in the Raman spectrum of graphene
and Raman scattering mechanism . 22
D.2 Example – Influence of edges in the Raman spectrum of graphene . 22
D.3 Example – Influence of defect in the Raman spectrum of single layer
graphene . 24
D.4 Example – Raman characteristics of reduced graphene sheet . 26
D.5 Conclusion . 27
Bibliography . 28
Figure 1 – Schematic diagram of Raman scattering processes in realistic graphene
material . 6
Figure 2 – Different packing configurations of graphene flakes in film (left) and powder
(right) . 6
Figure 3 – Schematic drawing of Raman spectra of defective graphene (upper) and
pristine graphene (bottom) . 12
Figure 4 – Schematic drawing of sample preparation method . 12
Figure B.1 – Schematic drawing of five-point-sampling method . 17
Figure B.2 – Location of measurement points . 17
Figure C.1 – The field view of graphene sample beneath Raman microscope . 18
Figure C.2 – The procedure of Raman spectrum processing . 19
Figure C.3 – Typical Raman spectrum after processing . 20
Figure C.4 – The overall defect level of one test sample . 21
Figure C.5 – Measurement results of different testing organizations . 21
Figure D.1 – Characteristic bands in the Raman spectrum of graphene and Raman
processes [6] . 22
Figure D.2 – Raman spectra from the edges of a monolayer graphene sample [9] . 23
Figure D.3 – Raman spectra obtained from monolayer graphene samples with
hexagonal and circular holes [10] . 23
Figure D.4 – Raman spectra for four different ion doses in graphene [1] . 24
Figure D.5 – E [I /I ] as a function of L [2] . 24
L D G D
Figure D.6 – (a) Definition of the activated A-region (green) and structurally-
disordered S-region (red). (b-e) Snapshots of the structural evolution of the graphene
sheet for different defect concentrations [1] . 25
Figure D.7 – Evolution of 2D and other second-order bands with increasing ion doses
[5] . 25
Figure D.8 – Raman characteristics of as-made graphene sheet and different types of
reduced graphene sheet film samples: (a) Raman spectra; (b) D/G intensity ratios; (c)
S3/2D intensity ratios [7] . 26
Figure D.9 – Resistivity of as-made graphene sheet and different types of reduced
graphene sheet [7] . 26
Table A.1 – Product identification (in accordance with IEC 62565-3-1) . 15
Table A.2 – General material description (in accordance with IEC 62565-3-1). 15
Table A.3 – Information related with test . 16
Table A.4 – Measurement results . 16
Table C.1 – Average I ′/I of each test point . 20
D+D 2D
– 4 – IEC TS 62607-6-14:2020 IEC:2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
NANOMANUFACTURING – KEY CONTROL CHARACTERISTICS –
Part 6-14: Graphene-based material – Defect level: Raman spectroscopy
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies
...