|
IEC TS 60034-34
Edition 1.0 2020-11
TECHNICAL
SPECIFICATION
colour
inside
Rotating electrical machines –
Part 34: AC adjustable speed rolling mill motors
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de
CH-1211 Geneva 20
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.
need further assistance, please contact the Customer Service
.
IEC TS 60034-34
Edition 1.0 2020-11
TECHNICAL
SPECIFICATION
colour
inside
Rotating electrical machines –
Part 34: AC adjustable speed rolling mill motors
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.160.01 ISBN 978-2-8322-9046-0
– 2 – IEC TS 60034-34:2020 © IEC 2020
CONTENTS
FOREWORD . 6
INTRODUCTION . 8
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 9
3.1 Terms and definitions . 9
3.2 Terms and definitions for adjustable speed control and rolling operation . 13
3.3 Terms and definitions for adjustable speed drive system . 14
3.4 Terms and definitions for monitoring and protection sequence . 15
3.5 Terms and definitions for motor installation and site trial operation . 15
3.6 Terms and definitions for test . 16
4 Terminal voltage determination . 17
5 Duty type and temperature class . 19
5.1 General . 19
5.2 Selection of rolling operation pattern . 19
5.3 Evaluation of winding temperature deviation during one rolling cycle . 20
5.4 Duty type S1 or S9 selection . 20
5.5 Class B rise or Class F rise selection . 21
5.6 Overload current duration time limit based on winding temperature deviation
in one rolling cycle for RMS current of 100 % . 21
6 Continuous overload capability . 22
6.1 General . 22
6.2 Relative thermal life index of TL value estimation by simplified method . 23
6.3 Relative thermal life estimation by precise method . 24
6.4 Relative thermal life index of TL value determination by precise method . 25
7 Mechanical requirements . 25
7.1 General . 25
7.2 Mechanical strength for shaft and other transmission parts considering
torsional vibration . 25
7.3 Vibration transmitted through the motor base . 25
7.4 Tangential forces applied to rotor and stator . 25
7.5 Thrust load . 25
7.5.1 General . 25
7.5.2 Frequently applied thrust load . 25
7.5.3 Occasionally applied maximum thrust load . 26
7.5.4 Emergency maximum thrust load . 26
7.6 Radial load for bearings . 26
7.7 Overspeed . 26
7.8 Stator coil end fixation . 26
7.9 Stator shift construction for maintenance inspection. 26
7.10 Mounting code application . 26
8 Withstand voltage capability . 26
8.1 Rotor bars or damper bars and short-circuit rings . 26
8.2 General . 27
8.3 Withstand voltage test . 27
8.4 Withstand voltage capability . 27
8.4.1 General . 27
8.4.2 Ground insulation . 27
8.4.3 Turn-to-turn insulation . 29
9 Factory tests and recommended site operation tests . 29
9.1 General . 29
9.1.1 General scope for the tests . 29
9.1.2 Requirements of the site operation test where vector control is applied . 29
9.2 Factory test . 30
9.3 Preparation before trial operation at site . 30
9.3.1 General . 30
9.3.2 Calibration of feedback signals for the converter . 31
9.3.3 Insulation resistance tests for motor . 31
9.3.4 Insulation resistance tests for bearings . 31
9.3.5 Performance test for bearing lubrication oil supply unit . 31
9.3.6 Confirmation of lubrication oil surface level for bearings . 31
9.3.7 Performance test for cooling systems . 31
9.3.8 Confirmation of alarm issue levels for motor protection . 31
9.3.9 Synchronous motor pole position confirmation test . 32
9.4 Site uncoupled trial operation . 32
9.4.1 General . 32
9.4.2 Rotational speed build-up test . 32
9.4.3 Bearing temperature rise test . 32
9.5 Site no-load characteristic test . 32
9.5.1 Induction motor no-load characteristics test . 32
9.5.2 Synchronous motor no-load characteristics test . 33
9.5.3 No-load characteristics test record. 33
9.6 Site acceleration and deceleration test . 33
10 Grounding . 34
10.1 General . 34
10.2 Protection against bearing currents . 34
10.3 Protective earthing (PE) . 34
10.4 Functional earthing (FE) . 34
11 Rating plate . 35
Annex A (normative) Short-time overload capability . 36
A.1 General . 36
A.2 Frequently applied Art-1 short-time overload capability specification . 36
A.3 Frequently applied Art-2 short-time overload capability specification . 39
Annex B (normative) Rolling operation pattern designation . 42
B.1 General . 42
B.2 Rolling operation pattern for hot reversing rolling . 42
B.3 Rolling operation pattern for hot continuous rolling of sheet strip . 43
B.4 Rolling operation pattern for continuous caster directly connected hot
continuous rolling mills . 44
B.5 Rolling operation pattern for hot continuous rolling for wire and rod mills . 45
B.6 Rolling operation pattern for cold reversing rolling mills . 46
B.7 Rolling operation pattern for cold continuous rolling . 47
B.8 Operation pattern for coilers and reels . 48
Annex C (informative) Determination of winding temperature deviation in one rolling
cycle . 50
– 4 – IEC TS 60034-34:2020 © IEC 2020
C.1 General . 50
C.2 Simplified method for estimation of the winding temperature deviation
between maximum and mean values in one rolling cycle . 50
C.3 Precise method for estimation of the winding temperature deviation between
maximum and mean in one rolling cycle .
...