|
SLOVENSKI STANDARD
SIST EN 60519-12:2018
01-maj-2018
1DGRPHãþD
SIST EN 60519-12:2013
9DUQRVWSULHOHNWULþQLKJUHOQLKLQãWDODFLMDKLQHOHNWURPDJQHWQLREGHODYLGHO
3RVHEQH]DKWHYH]DLQãWDODFLMH]LQIUDUGHþLPHOHNWULþQLPRJUHYDQMHP
Safety in installations for electroheating and electromagnetic processing - Part 12:
Particular requirements for infrared electroheating
Ta slovenski standard je istoveten z: EN IEC 60519-12:2018
ICS:
97.100.10 (OHNWULþQLJUHOQLNL Electric heaters
SIST EN 60519-12:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN 60519-12:2018
SIST EN 60519-12:2018
EUROPEAN STANDARD EN IEC 60519-12
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2018
ICS 25.180.10 Supersedes EN 60519-12:2013
English Version
Safety in installations for electroheating and electromagnetic
processing - Part 12: Particular requirements for infrared
electroheating
(IEC 60519-12:2016)
Sécurité dans les installations destinées au traitement Sicherheit in Elektrowärmeanlagen und Anlagen für
électrothermique et électromagnétique - Partie 12: elektromagnetische Bearbeitungsprozesse - Teil 12:
Exigences particulières pour chauffage électrique par Besondere Anforderungen an Infrarot-Elektrowärmeanlagen
rayonnement infrarouge (IEC 60519-12:2016)
(IEC 60519-12:2016)
This European Standard was approved by CENELEC on 2017-01-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60519-12:2018 E
SIST EN 60519-12:2018
European foreword
The text of document 27/967/CDV, future edition 2 of IEC 60519-12, prepared by IEC/TC 27
"Industrial electroheating and electromagnetic processing" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 60519-12:2018.
The following dates are fixed:
• latest date by which the document has to be (dop) 2018-09-02
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2021-03-02
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60519-12:2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60519-12:2016 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60519-2:2006 NOTE Harmonized as EN 60519-2:2006 (not modified).
IEC 60825-1:2014 NOTE Harmonized as EN 60825-1:2014 (not modified).
IEC 61010-1:2010 NOTE Harmonized as EN 61010-1:2010 (not modified).
SIST EN 60519-12:2018
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60519-1 2015 Safety in installations for electroheating EN 60519-1 2015
and electromagnetic processing -- Part 1:
General requirements
SIST EN 60519-12:2018
SIST EN 60519-12:2018
IEC 60519-12
Edition 2.0 2016-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Safety in installations for electroheating and electromagnetic processing –
Part 12: Particular requirements for infrared electroheating
Sécurité dans les installations destinées au traitement électrothermique et
électromagnétique –
Partie 12: Exigences particulières pour chauffage électrique par rayonnement
infrarouge
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.180.10 ISBN 978-2-8322-3709-0
SIST EN 60519-12:2018
– 2 – IEC 60519-12:2016 © IEC 2016
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope and object . 7
2 Normative references . 8
3 Terms, definitions and abbreviations . 8
4 Classification and sub-division . 10
5 Risk assessment . 11
6 General provisions. 11
7 Protection against electric shock . 11
8 Protection against hazards caused by electric or magnetic nearfields . 11
9 Protection against hazards from radiation . 11
10 Protection against hazards from thermal influences . 13
11 Protection against hazards from fire . 13
12 Protection against hazards from fluids . 13
13 Specific requirements for components and subassemblies . 13
14 Control of the installation or equipment . 13
15 Protection against mechanical hazards . 13
16 Protection against hazards resulting from use . 13
17 Protection against other hazards . 13
18 Verification and testing . 13
19 Information for use . 14
Annex A (informative) List of significant hazards . 15
Annex B (informative) Electric and magnetic fields, touch currents – limits of
exposure hazards . 16
Annex C (informative) Optical radiation – limits of exposure hazards . 17
Annex D (informative) Limits for exposure hazards – noise and vibration . 19
Annex E (normative) Provisions concerning EMC . 20
Annex F (normative) Marking and warning . 21
Annex G (informative) Guidelines on using this standard . 22
Annex H (informative) Connection with ISO 13577 series . 23
Annex AA (informative) Procedure for reducing risk from infrared radiation . 24
Annex BB (informative) Simplified measurement method for the assessment of
thermal infrared radiation exposure . 26
Annex CC (informative) Measurement device for total irradiance . 32
Bibliography . 33
Figure C.101 – Risk groups and exposure limits (refer to Table C.1 of
IEC 60519-1:2015) depending on time of exposure and irradiation. 17
Figure C.102 – Risk groups and exposure limits (refer to Table C.2 of
IEC 60519-1:2015) depending on time of exposure and radiance . 18
Figure BB.1 – Factors for converting measured total irradiance into band irradiance,
depending on surface temperature of a grey emitter generating the signal . 28
SIST EN 60519-12:2018
IEC 60519-12:2016 © IEC 2016 – 3 –
Figure BB.2 – Factor for converting measured total radiance into relevant retinal
thermal radiance, depending on surface temperature of a grey emitter generating the
signal . 31
Figure CC.1 – Example of a detector for total irradiance measurement . 32
Table AA.1 – Procedure for assessment and reduction of radiation exposure through
design . 25
Table BB.1 – Measurement procedure . 26
SIST EN 60519-12:2018
– 4 – IEC 60519-12:2016 © IEC 2016
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SAFETY IN INSTALLATIONS FOR ELECTROHEATING
AND ELECTROMAGNETIC PROCESSING –
Part 12: Particular requirements for infrared electroheating
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out
...