|
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Classification des conditions d'environnement - Partie 3: Classification des groupements des agents d'environnement et de leurs sévérités - Section 2: Transport (IEC 60721-3-2:2018)Classification of environmental conditions - Part 3-2: Classification of groups of environmental parameters and their severities - Transportation and Handling (IEC 60721-3-2:2018)19.040Preskušanje v zvezi z okoljemEnvironmental testingICS:Ta slovenski standard je istoveten z:EN IEC 60721-3-2:2018SIST EN IEC 60721-3-2:2018en01-junij-2018SIST EN IEC 60721-3-2:2018SLOVENSKI
STANDARDSIST EN 60721-3-2:20011DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN IEC 60721-3-2
April 2018 ICS 19.040
Supersedes
EN 60721-3-2:1997
English Version
Classification of environmental conditions - Part 3-2: Classification of groups of environmental parameters and their severities - Transportation and Handling (IEC 60721-3-2:2018)
Classification des conditions d'environnement - Partie 3-2: Classification des groupements des agents d'environnement et de leurs sévérités - Transport et manutention (IEC 60721-3-2:2018)
Klassifizierung von Umgebungsbedingungen - Teil 3-2: Klassifizierung von Einflussgrößen in Gruppen und deren Schärfegrade - Transport und Handhabung (IEC 60721-3-2:2018) This European Standard was approved by CENELEC on 2018-03-30. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23,
B-1040 Brussels © 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60721-3-2:2018 E SIST EN IEC 60721-3-2:2018
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-12-30 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021-03-30
This document supersedes EN 60721-3-2:1997.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60721-3-2:2018 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60721-2 (series) NOTE Harmonized as EN 60721-2 (series). IEC 60721-2-1 NOTE Harmonized as EN 60721-2-1. IEC 60721-2-2 NOTE Harmonized as EN 60721-2-2. IEC 60721-2-3 NOTE Harmonized as EN 60721-2-3. IEC 60721-2-9 NOTE Harmonized as EN 60721-2-9. IEC 60721-3 (series) NOTE Harmonized as EN 60721-3 (series). IEC 60721-3-0 NOTE Harmonized as EN 60721-3-0. IEC 60721-3-1 NOTE Harmonized as EN 60721-3-1. SIST EN IEC 60721-3-2:2018
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1
Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2
Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.
Publication Year Title EN/HD Year IEC 60721-1 -
Classification of environmental conditions -- Part 1: Environmental parameters and their severities EN 60721-1 -
IEC 60721-3-2 Edition 3.0 2018-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Classification of environmental conditions – Part 3-2: Classification of groups of environmental parameters and their severities – Transportation and handling
Classification des conditions d’environnement –
Partie 3-2: Classification des groupements des agents d’environnement et de leurs sévérités – Transport et manutention INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 19.040
ISBN 978-2-8322-5374-8
– 2 – IEC 60721-3-2:2018 © IEC 2018
CONTENTS FOREWORD . 3 1 Scope and object . 5 2 Normative references . 5 3 Terms and definitions. 5 4 General . 6 5 Classification of groups of environmental parameters and their severities . 7 5.1 General . 7 5.2 K Climatic conditions . 7 5.3 B Biological conditions . 9 5.4 C Chemically active substances . 9 5.5 S Mechanically active substances . 10 5.6 M Mechanical conditions . 11 Annex A (informative)
Chemically active substances . 15 Bibliography . 16
Figure 1 – Consolidation of vibration conditions . 13 Figure 2 – Consolidation of mechanical conditions . 14
Table 1 – Classification of climatic conditions . 8 Table 2 – Classification of biological conditions . 9 Table 3 – Classification of chemically active substances . 10 Table 4 − Classification of mechanically active substances . 11 Table 5 – Classification of mechanical conditions . 11
– 3 – IEC 60721-3-2:2018 © IEC 2018
INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
CLASSIFICATION OF ENVIRONMENTAL CONDITIONS –
Part 3-2: Classification of groups of environmental parameters and their severities – Transportation and handling
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60721-3-2 has been prepared by IEC technical committee 104: Environmental conditions, classification, and methods of test. This third edition cancels and replaces the second edition, published in 1997, and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Clause 1: reworded and added handling. b) Clause 2: updated normative references. c) Clause 3: updated definitions. d) Clause 4: reworded and simplified.
– 4 – IEC 60721-3-2:2018 © IEC 2018
e) Clause 5: revised and updated. Several classes have been replaced by completely new classes based on the use of new information obtained from referenced Technical Reports.
f) Table 1 through Table 5: updated. g) Table 6 added.
h) Old annexes A to C removed except Clause A.3 that is incorporated in Clause 5. i) New Annex A. The text of this International Standard is based on the following documents: FDIS Report on voting 104/773/FDIS 104/783/RVD
Full information on the voting for the approval of this International Standard can be found in the report on voting indicated in the above table. This document has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 60721 series, published under the general title Classification of environmental conditions, can be found on the IEC website. The committee has decided that the contents of this document will remain unchanged until the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to the specific document. At this date, the document will be
• reconfirmed, • withdrawn, • replaced by a revised edition, or • amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer.
– 5 – IEC 60721-3-2:2018 © IEC 2018
CLASSIFICATION OF ENVIRONMENTAL CONDITIONS –
Part 3-2: Classification of groups of environmental parameters and their severities – Transportation and handling
1 Scope and object This part of IEC 60721 classifies the groups of environmental parameters and their severities to which a product is subjected while being transported and handled. The most commonly used methods of transportation and handling have been taken into account, including the following: – road transport: cars, tru
...