|
SLOVENSKI STANDARD
01-julij-2018
1DGRPHãþD
SIST EN 60730-2-13:2008
$YWRPDWVNHHOHNWULþQHNUPLOQHQDSUDYHGHO 3RVHEQH]DKWHYH]D]D]QDYDOD
VHQ]RUMH YODJH
Automatic electrical controls - Part 2-13: Particular requirements for humidity sensing
controls
Automatische elektrische Regel- und Steuergeräte für den Hausgebrauch und ähnliche
Anwendungen - Teil 2-13: Besondere Anforderungen an feuchtigkeitsempfindliche Regel
- und Steuergeräte
Dispositifs de commande électrique automatiques à usage domestique et analogue -
Partie 2-13: Règles particulières pour les dispositifs de commande sensibles à l'humidité
Ta slovenski standard je istoveten z: EN IEC 60730-2-13:2018
ICS:
97.120 Avtomatske krmilne naprave Automatic controls for
za dom household use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60730-2-13
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2018
ICS 97.120 Supersedes EN 60730-2-13:2008
English Version
Automatic electrical controls - Part 2-13: Particular requirements
for humidity sensing controls
(IEC 60730-2-13:2017)
Dispositifs de commande électrique automatiques - Partie Automatische elektrische Regel- und Steuergeräte für den
2-13: Règles particulières pour les dispositifs de commande Hausgebrauch und ähnliche Anwendungen - Teil 2-13:
sensibles à l'humidité Besondere Anforderungen an feuchtigkeitsempfindliche
(IEC 60730-2-13:2017) Regel- und Steuergeräte
(IEC 60730-2-13:2017)
This European Standard was approved by CENELEC on 2017-11-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60730-2-13:2018 E
European foreword
The text of document 72/1078/FDIS, future edition 3 of IEC 60730-2-13, prepared by IEC/TC 72
"Automatic electrical controls", was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60730-2-13:2018.
The following dates are fixed:
(dop) 2018-10-13
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2021-04-13
• latest date by which the national standards conflicting with
the document have to be withdrawn
This document supersedes EN 60730-2-13:2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60730-2-13:2017 was approved by CENELEC as a
European Standard without any modification.
IEC 60730-2-13
Edition 3.0 2017-10
INTERNATIONAL
STANDARD
Automatic electrical controls –
Part 2-13: Particular requirements for humidity sensing controls
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 97.120 ISBN 978-2-8322-4900-0
– 2 – IEC 60730-2-13:2017 © IEC 2017
CONTENTS
FOREWORD . 3
1 Scope and normative references . 5
2 Terms and definitions . 5
3 General requirements . 6
4 General notes on tests . 6
5 Rating. 6
6 Classification . 6
7 Information . 6
8 Protection against electric shock . 6
9 Provision for protective earthing . 6
10 Terminals and terminations . 6
11 Constructional requirements . 6
12 Moisture and dust resistance . 6
13 Electric strength and insulation resistance . 7
14 Heating . 7
15 Manufacturing deviation and drift . 7
16 Environmental stress . 7
17 Endurance . 7
18 Mechanical strength . 8
19 Threaded parts and connections . 8
20 Creepage distances, clearances and distances through solid insulation . 8
21 Resistance to heat, fire and tracking . 8
22 Resistance to corrosion . 8
23 Electromagnetic compatibility (EMC) requirements – Emission . 8
24 Components . 8
25 Normal operation . 9
26 Electromagnetic compatibility (EMC) requirements – Immunity . 9
27 Abnormal operation . 9
28 Guidance on the use of electronic disconnection . 9
Annex H (normative) Requirements for electronic controls . 9
Annex AA (normative) Independently mounted and in-line cord controls . 16
Annex BB (normative) Regional differences . 17
Annex CC (informative) Specific regional requirements in Japan . 19
Bibliography . 20
Table H.101 – Compliance criteria . 11
Table AA.1 – Number of cycles . 16
Table BB.1 – Minimum number of cycles for independently mounted and in-line cord
controls (United States) . 17
Table BB.2 – Minimum number of cycles for independently mounted and in-line cord
controls (Canada) . 18
IEC 60730-2-13:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
AUTOMATIC ELECTRICAL CONTROLS –
Part 2-13: Particular requirements for humidity sensing controls
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60730-2-13 has been prepared by IEC technical committee 72:
Automatic electrical controls.
The text of this standard is based on the following documents:
FDIS Report on voting
72/1078/FDIS 72/1108/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
This third edition cancels and replaces the second edition published in 2006. This edition
constitutes a technical revision. This edition includes alignment with the text of 60730-1 fifth
edition and the following significant technical changes with respect to the previous edition:
– 4 – IEC 60730-2-13:2017 © IEC 2017
a) alignment of the EMC requirements in Clause H.26 to those in other part 2 standards;
b) addition of requirements in Clause H.27 to cover class B and C control functions of
humidity sensing controls.
This Part 2-13 is intended to be used in conjunction with IEC 60730-1. It was established on
the basis of the fifth edition of that standard (2013). Consideration may be given to future
editions of, or amendments to, IEC 60730-
...