|
SLOVENSKI STANDARD
01-junij-2021
Nadomešča:
SIST EN 61290-1-3:2015
Optični ojačevalniki - Preskusne metode - 1-3. del: Parametri moči in ojačenja -
Metoda z merilnikom optične moči (IEC 61290-1-3:2021)
Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power
meter method (IEC 61290-1-3:2021)
Prüfverfahren für Lichtwellenleiter-Verstärker - Teil 1-3: Optische Leistungs- und
Verstärkerparameter - Verfahren mit optischem Leistungsmessgerät (IEC 61290-1-
3:2021)
Amplificateurs optiques - Méthodes d'essai - Partie 1-3: Paramètres de puissance et de
gain - Méthode par appareil de mesure de la puissance optique (IEC 61290-1-3:2021)
Ta slovenski standard je istoveten z: EN IEC 61290-1-3:2021
ICS:
33.180.30 Optični ojačevalniki Optic amplifiers
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61290-1-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2021
ICS 33.180.30 Supersedes EN 61290-1-3:2015 and all of its
amendments and corrigenda (if any)
English Version
Optical amplifiers - Test methods - Part 1-3: Power and gain
parameters - Optical power meter method
(IEC 61290-1-3:2021)
Amplificateurs optiques - Méthodes d'essai - Partie 1-3: Prüfverfahren für Lichtwellenleiter-Verstärker - Teil 1-3:
Paramètres de puissance et de gain - Méthode par appareil Leistungs- und Verstärkerparameter - Verfahren mit
de mesure de la puissance optique optischem Leistungsmessgerät
(IEC 61290-1-3:2021) (IEC 61290-1-3:2021)
This European Standard was approved by CENELEC on 2021-04-05. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61290-1-3:2021 E
European foreword
The text of document 86C/1671/CDV, future edition 4 of IEC 61290-1-3, prepared by SC 86C "Fibre
optic systems and active devices" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 61290-1-3:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-01-05
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-04-05
document have to be withdrawn
This document supersedes EN 61290-1-3:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61290-1-3:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60793-1-1 NOTE Harmonized as EN 60793-1-1
IEC 60793-1-40 NOTE Harmonized as EN IEC 60793-1-40
IEC 60825-1 NOTE Harmonized as EN 60825-1
IEC 60825-2 NOTE Harmonized as EN 60825-2
IEC 61290-1 NOTE Harmonized as EN 61290-1
IEC 61290-1-1 NOTE Harmonized as EN IEC 61290-1-1
IEC 61290-10 (series) NOTE Harmonized as EN IEC 61290-10 (series)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60793-2-50 - Optical fibres - Part 2-50: Product EN IEC 60793-2-50 -
specifications - Sectional specification for
class B single-mode fibres
IEC 61291-1 - Optical amplifiers – Part 1: Generic EN IEC 61291-1 -
specification
IEC 61290-1-3
Edition 4.0 2021-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Optical amplifiers – Test methods –
Part 1-3: Power and gain parameters – Optical power meter method
Amplificateurs optiques – Méthodes d'essai –
Partie 1-3: Paramètres de puissance et de gain – Méthode par appareil de
mesure de la puissance optique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.30 ISBN 978-2-8322-9475-8
– 2 – IEC 61290-1-3:2021 © IEC 2021
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviated terms . 5
3.1 Terms and definitions . 5
3.2 Abbreviated terms . 6
4 Apparatus . 7
5 Test sample . 9
6 Procedure . 9
7 Calculation . 12
8 Test results . 13
Annex A (informative) Optimization of optical bandpass filter spectral width . 15
Bibliography . 16
Figure 1 – Typical arrangement of optical power meter test apparatus for measurement . 7
IEC 61290-1-3:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL AMPLIFIERS – TEST METHODS –
Part 1-3: Power and gain parameters – Optical power meter method
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61290-1-3 has been prepared by subcommittee 86C: Fibre optic systems and active
devices, of IEC technical committee 86: Fibre optics. It is an International Standard.
This fourth edition cancels and replaces the third edition published in 2015. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) harmonization with IEC 61290-1-1;
b) use of the term "measurement uncertainty" instead of "measurement accuracy".
– 4 – IEC 61290-1-3:2021 © IEC 2021
The text of this International Standard is based on the following documents:
Draft Report on voting
86C/1671/CDV 86C/1698/RVC
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at /members_experts/refdocs. The main document types developed by IEC are
described in greater detail at /standardsdev/publications.
A list of all parts in the IEC 61290 series, published under the general title Optical amplifiers –
Test methods, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IEC 61290-1-3:2021 © IEC 2021 – 5 –
OPTICAL AMPLIFIERS – TEST METHODS –
Part 1-3: Power and gain parameters – Optical power meter method
1 Scope
This part of IEC 61290 applies to all commercially available optical amplifiers (OA) and optically
amplified subsystems. It applies to OA using optically pumped fibres (OFA based on either rare-
earth doped fibres or on the Raman effect), semiconductors (SOA), and waveguides (POWA).
NOTE 1 The applicability of the test methods described in this document to dis
...