|
SLOVENSKI STANDARD
01-julij-2021
Nadomešča:
SIST EN 61439-2:2012
Sestavi nizkonapetostnih stikalnih in krmilnih naprav - 2. del: Sestavi močnostnih
stikalnih in krmilnih naprav (IEC 61439-2:2020)
Low-voltage switchgear and controlgear assemblies - Part 2: Power switchgear and
controlgear assemblies (IEC 61439-2:2020)
Niederspannungs-Schaltgerätekombinationen - Teil 2: Energie-
Schaltgerätekombinationen (IEC 61439-2:2020)
Ensembles d'appareillage à basse tension - Partie 2: Ensembles d'appareillage de
puissance (IEC 61439-2:2020)
Ta slovenski standard je istoveten z: EN IEC 61439-2:2021
ICS:
29.130.20 Nizkonapetostne stikalne in Low voltage switchgear and
krmilne naprave controlgear
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61439-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2021
ICS 29.130.20 Supersedes EN 61439-2:2011 and all of its amendments
and corrigenda (if any)
English Version
Low-voltage switchgear and controlgear assemblies - Part 2:
Power switchgear and controlgear assemblies
(IEC 61439-2:2020)
Ensembles d'appareillage à basse tension - Partie 2: Niederspannungs-Schaltgerätekombinationen - Teil 2:
Ensembles d'appareillage de puissance Energie-Schaltgerätekombinationen
(IEC 61439-2:2020) (IEC 61439-2:2020)
This European Standard was approved by CENELEC on 2020-08-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61439-2:2021 E
European foreword
The text of document 121B/104/FDIS, future edition 3 of IEC 61439-2, prepared by SC 121B "Low-
voltage switchgear and controlgear assemblies" of IEC/TC 121 "Switchgear and controlgear and their
assemblies for low voltage" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61439-2:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-11-21
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-05-21
document have to be withdrawn
This document supersedes EN 61439-2:2011 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 61439-2:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60269 (series) NOTE Harmonized as EN 60269 (series)
IEC 60898 (series) NOTE Harmonized as EN 60898 (series)
IEC 60947 (series) NOTE Harmonized as EN IEC 60947 (series)
IEC 61008 (series) NOTE Harmonized as EN 61008 (series)
IEC 61009 (series) NOTE Harmonized as EN 61009 (series)
IEC 61427-1:2013 NOTE Harmonized as EN 61427-1:2013 (not modified)
IEC 61010-2-201 NOTE Harmonized as EN IEC 61010-2-201
IEC 61800-5-1 NOTE Harmonized as EN 61800-5-1
IEC 62093 NOTE Harmonized as EN 62093
IEC 62124 NOTE Harmonized as EN 62124
IEC 62423 NOTE Harmonized as EN 62423
IEC 62446-1:2016 NOTE Harmonized as EN 62446-1:2016 (not modified)
IEC 62446-1:2016/A1:2018 NOTE Harmonized as EN 62446-1:2016/A1:2018 (not modified)
IEC 62790 NOTE Harmonized as EN IEC 62790
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Annex ZA of EN IEC 61439-1:2021 applies with the following addition:
Publication Year Title EN/HD Year
IEC 60204-1 2016 Safety of machinery – Electrical equipment EN 60204-1 2018
of machines – Part 1: General
requirements
IEC 60947-3 2020 Low-voltage switchgear and controlgear – EN IEC 60947-3 2021
Part 3: Switches, disconnectors, switch-
disconnectors and fuse-combination units
IEC 61140 2016 Protection against electric shock – EN 61140 2016
Common aspects for installation and
equipment
IEC 61439-1 2020 Low-voltage switchgear and controlgear EN IEC 61439-1 2021
assemblies – Part 1: General rules
IEC 62262 2002 Degrees of protection provided by EN 62262 2002
enclosures for electrical equipment against
external mechanical impacts (IK code)
Annex ZZ
(informative)
Relationship between this European standard and the safety
objectives of Directive 2014/35/EU [2014 OJ L96] aimed to be
covered
This European standard has been prepared under a Commission’s standardisation request relating to
harmonised standards in the field of the Low Voltage Directive, M/511, to provide one voluntary means
of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of the
Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the
making available on the market of electrical equipment designed for use within certain voltage limits
[2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding safety objectives of
that Directive, and associated EFTA regulations.
Table ZZ.1 — Correspondence between this European standard and Annex I of Directive
2014/35/EU [2014 OJ L96]
Clause(s) / sub-clause(s)
Safety objectives of Directive
Remarks / Notes
2014/35/EU
of this EN
(1)(a) Clauses 6, annex DD.6
(1)(b) Clauses 6, annex DD.6
(1)(c) See safety objectives 2 a) to 2 d) and
3 a) to 3 c) in this table
(2)(a) Clauses 8.2, 8.3, 8.4, 8.5, 8.101, 10.5,
10.6, 10.9, 11.4, 11.5, annex DD.8.1.1,
annex DD.8.2, annex DD.8.4,
annex DD.5
(2)(b) Clauses 7.1, 7.2, 8.1, 8.2, 8.3, 8.4, 8.5,
8.6, 8.7, 9.1, 9.2, 9.3, 10.2, 10.3, 10.4,
10.5, 10.6, 10.7, 10.9, 10.10, 10.11,
11.2, 11.3, 11.4, 11.5, 11.6, 11.9,
annex DD.7, annex DD.8,
annex DD.9.1, annex DD.10.10
(2)(c) Clauses 6.2, 7.2, 8.1, 8.2, 8.5, 8.101,
9.2, 9.3, 9.4, 10.2, 10.3, 10.6, 10.10,
10.11, 11.2, 11.5, 11.8, annex J,
annex DD.6.2, annex DD.8.2,
annex DD.10.10
(2)(d) Clauses 5, 8.1, 8.2, 8.3, 8.4, 8.5, 8.6,
8.7, 9.1, 9.2, 9.3, 8.101, 10.2, 10.3,
10.4, 10.5, 10.6, 10.7, 10.9, 10.10,
10.11, 11.2, 11.3, 11.4, 11.5, 11.9,
11.10, annex DD.5.2, annex DD.8.1.1,
annex DD.8.2.2, annex DD.8.4,
annex DD.9.1, annex DD.10
Clause(s) / sub-clause(s)
Safety objectives of Directive
Remarks / Notes
2014/35/EU
of this EN
(3)(a) Clauses 6.2, 7.2, 8.1, 8.2, 8.101, 9.3,
10.2, 10.11, 11.8, annex DD.6.2,
annex DD.8.2
(3)(b) Clause 7.1, 7.2, 8.1, 8.2, ,8.3, 8.7, 9.1,
9.2, 9.3, 9.4, 10.2, 10.3, 10.4, 10.6,
10.9, 10.10, 10.11, 10.12, 11.2, 11.3,
11.9, annex DD.7 annex DD.8.2,
annex DD.8.101, annex DD.8.102,
annex DD.9.1, annex DD.10.10,
annex DD.10.101, annex DD.10.102
(3)(c) Clauses 5.3, 5.4, 8.1, 8.5, 8.6, 9.2, 9.3,
10.2, 10.5, 10.6, 10.7, 10.10, 10.11,
11.4, 11.5, 11.6, 11.8, 11.10, annex E,
annex I, annex P, annex D.5.3,
annex DD.5.4, annex DD.8.5,
annex DD.10.10
WARNING 1: Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2: Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
IEC 61439-2
Edition 3.0 2020-07
INTERNATIONAL
STANDARD
Low-voltage switchgear and controlgear assemblies –
Part 2: Power switchgear and controlgear assemblies
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.130.20 ISBN 978-2-8322-8587-9
– 2 – IEC 61439-2:2020 © IEC 2020
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 6
3 Terms and definitions . 6
4 Symbols and abbreviations . 9
5 Interface characteristics . 9
6 Information . 10
7 Service conditions . 11
8 Constructional requirements . 11
9 Performance requirements . 14
10 Design verification . 15
11 Routine verification . 19
Annexes . 22
Annex AA (informative) Items subject to agreement between the PSC-assembly
manufacturer and the user . 23
Annex BB (informative) Forms of internal separation (see 8.101) . 27
Annex CC (informative) Determining power loss by measurement for circuits
exceeding 1600 A in a reference design . 32
Annex DD (informative) Assemblies for use in photovoltaic installations . 34
Annex EE (informative) Items subject to agreement between the photovoltaic
assembly (PVA) manufacturer and the user . 43
Annex FF (informative) Design verification (PVA only) . 47
Annex GG (informative) List of notes concerning certain countries . 49
Bibliography . 50
Figure BB.1 – Symbols used in Figures BB.2, BB.3 and BB.4 . 27
Figure BB.2 – Forms 1 and 2 . 29
Figure BB.3 – Form 3 . 30
Figure BB.4 – Form 4 . 31
Figure CC.1 – Power loss measurement .
...