|
SLOVENSKI STANDARD
01-september-2018
'LQDPLþQLPRGXOLGHO 3UHGORJH]DWHKQLþQHVSHFLILNDFLMH0XOWLPHGLMVND
RSWLþQDVWLNDOD ,(&
Dynamic modules - Part 3-4: Performance specification templates - Multicast optical
switches (IEC 62343-3-4:2018)
Modules dynamiques - Partie 3-4: Modèles de spécification de performance -
Interrupteur optique multidiffusion (IEC 62343-3-4:2018)
Ta slovenski standard je istoveten z: EN IEC 62343-3-4:2018
ICS:
33.180.01 6LVWHPL]RSWLþQLPLYODNQLQD Fibre optic systems in
VSORãQR general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 62343-3-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2018
ICS 33.180.01, 33.180.99
English Version
Dynamic modules - Part 3-4: Performance specification
templates - Multicast optical switches
(IEC 62343-3-4:2018)
Modules dynamiques - Partie 3-4: Modèles de spécification Dynamische Module - Teil 3-4: Vorlagen für
de performance - Commutateurs optiques multidiffusions Leistungsspezifikationen - Optische Schalter für
(IEC 62343-3-4:2018) Mehrpunktverbindung
(IEC 62343-3-4:2018)
This European Standard was approved by CENELEC on 2018-06-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62343-3-4:2018 E
European foreword
The text of document 86C/1506/FDIS, future edition 1 of IEC 62343-3-4, prepared by SC 86C "Fibre
optic systems and active devices" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 62343-3-4:2018.
The following dates are fixed:
• latest date by which the document has to be (dop) 2019-03-01
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting (dow) 2021-06-01
with the document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 62343-3-4:2018 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60793-2-50 NOTE Harmonized as EN 60793-2-50
IEC 60875-1 NOTE Harmonized as EN 60875-1
IEC 60876-1:2014 NOTE Harmonized as EN 60876-1:2014 (not modified)
IEC 61000 series NOTE Harmonized as EN 61000 series
IEC 61300 series NOTE Harmonized as EN 61300 series
IEC 61753-1 NOTE Harmonized as EN 61753-1
IEC 61753-021-2 NOTE Harmonized as EN 61753-021-2
IEC 61753-081-2 NOTE Harmonized as EN 61753-081-2
IEC 61754 series NOTE Harmonized as EN 61754 series
IEC 61978-1 NOTE Harmonized as EN 61978-1
IEC 62343 NOTE Harmonized as EN 62343
IEC 62343-3-3 NOTE Harmonized as EN 62343-3-3
IEC 62343-4-1 NOTE Harmonized as EN 62343-4-1
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61290-7-1 - Optical amplifiers - Test methods -- Part EN 61290-7-1 -
7-1: Out-of-band insertion losses - Filtered
optical power meter method
IEC 61300-2-14 - Fibre optic interconnecting devices and EN 61300-2-14 -
passive components - Basic test and
measurement procedures -- Part 2-14:
Tests - High optical power
IEC 61300-3-2 - Fibre optic interconnecting devices and EN 61300-3-2 -
passive components - Basic test and
measurement procedures - Part 3-2:
Examination and measurements -
Polarization dependent loss in a single-
mode fibre optic device
IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures -- Part 3-3:
Examinations and measurements - Active
monitoring of changes in attenuation and
return loss
IEC 61300-3-6 - Fibre optic interconnecting devices and EN 61300-3-6 -
passive components - Basic test and
measurement procedures -- Part 3-6:
Examinations and measurements - Return
loss
IEC 61300-3-7 - Fibre optic interconnecting devices and - -
passive components - Basic test and
measurement procedures - Part 3-7:
Examinations and measurements -
Wavelength dependence of attenuation
and return loss of single mode
components
IEC 61300-3-20 - Fibre optic interconnecting devices and EN 61300-3-20 -
passive components - Basic test and
measurement procedures -- Part 3-20:
Examinations and measurements -
Directivity of fibre optic branching devices
IEC 61300-3-21 - Fibre optic interconnecting devices and EN 61300-3-21 -
passive components - Basic test and
measurement procedures - Part 3-21:
Examinations and measurements -
Switching time
IEC 61300-3-32 - Fibre optic interconnecting devices and EN 61300-3-32 -
passive components - Basic test and
measurement procedures -- Part 3-32:
Examinations and measurements -
Polarization mode dispersion
measurement for passive optical
components
IEC 61300-3-38 - Fibre optic interconnecting devices and EN 61300-3-38 -
passive components - Basic test and
measurement procedures - Part 3-
38:Examinations and measurements -
Group delay, chromatic dispersion and
phase ripple
IEC 61300-3-50 - Fibre optic interconnecting devices and EN 61300-3-50 -
passive components - Basic test and
measurement procedures -- Part 3-50:
Examinations and measurements -
Crosstalk for optical spatial switches
IEC 62343-1 2016 Dynamic modules - Part 1: Performance EN 62343-1 2016
standards - General conditions
IEC 62343-5-2 - Dynamic modules - Part 5-2: Test EN IEC 62343-5-2 -
methods - 1xN fixed-grid WSS - Dynamic
crosstalk measurement
IEC 62343-3-4
Edition 1.0 2018-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Dynamic modules –
Part 3-4: Performance specification templates – Multicast optical switches
Modules dynamiques –
Partie 3-4: Modèles de spécification de performance – Commutateurs optiques
multidiffusions
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.01; 33.180.99 ISBN 978-2-8322-5612-1
– 2 – IEC 62343-3-4:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Performance specification templates . 14
5 Electromagnetic compatibility (EMC) requirements . 18
Bibliography . 19
Figure 1 – Functional block diagram of the MCOS . 8
Figure 2 – Representation of latency time, rise time, fall time, bounce time, and
switching time . 13
Table 1 – General performance specification template for MCOS . 14
Table 2 – Optical performance specification template for MCOS . 15
Table 3 – Electrical and communication performance specification template for MCOS . 17
Table 4 – Mechanical performance specification template for MCOS . 18
IEC 62343-3-4:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DYNAMIC MODULES –
Part 3-4: Performance specification templates –
Multicast optical switches
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62343-3-4 has been prepared by subcommittee 86C: Fib
...