|
SLOVENSKI STANDARD
01-oktober-2021
Nadomešča:
SIST EN 61326-2-2:2013
Električna oprema za merjenje, nadzor in laboratorijsko uporabo - Zahteve za
elektromagnetno združljivost (EMC) - 2-2. del: Posebne zahteve - Preskusne
konfiguracije, obratovalni pogoji in merila učinkovitosti za prenosno preskusno
merilno opremo in opremo za nadzorovanje, ki se uporablja v nizkonapetostnih
distribucijskih sistemih (IEC 61326-2-2:2020)
Electrical equipment for measurement, control and laboratory use - EMC requirements -
Part 2-2: Particular requirements - Test configurations, operational conditions and
performance criteria for portable test, measuring and monitoring equipment used in low-
voltage distribution systems (IEC 61326-2-2:2020)
Elektrische Mess-, Steuer-, Regel- und Laborgeräte – EMV-Anforderungen – Teil 2-2:
Besondere Anforderungen – Prüfanordnung, Betriebsbedingungen und
Leistungsmerkmale für ortsveränderliche Prüf-, Mess- und Überwachungsgeräte für den
Gebrauch in Niederspannungs-Stromversorgungsnetzen (IEC 61326-2-2:2020)
Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la
CEM - Partie 2-2: Exigences particulières - Configurations d'essai, conditions de
fonctionnement et critères de performance des matériels portatifs d'essai, de mesure et
de surveillance utilisés dans des systèmes de distribution basse tension (IEC 61326-2-
2:2020)
Ta slovenski standard je istoveten z: EN IEC 61326-2-2:2021
ICS:
19.080 Električno in elektronsko Electrical and electronic
preskušanje testing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61326-2-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2021
ICS 17.220.20; 33.100.20; 25.040.40 Supersedes EN 61326-2-2:2013 and all of its
amendments and corrigenda (if any)
English Version
Electrical equipment for measurement, control and laboratory
use - EMC requirements - Part 2-2: Particular requirements -
Test configurations, operational conditions and performance
criteria for portable testing, measuring and monitoring equipment
used in low-voltage distribution systems
(IEC 61326-2-2:2020)
Matériel électrique de mesure, de commande et de Elektrische Mess-, Steuer-, Regel- und Laborgeräte - EMV-
laboratoire - Exigences relatives à la CEM - Partie 2-2: Anforderungen - Teil 2-2: Besondere Anforderungen -
Exigences particulières - Configurations d'essai, conditions Prüfanordnung, Betriebsbedingungen und
de fonctionnement et critères de performance des matériels Leistungsmerkmale für ortsveränderliche Prüf-, Mess- und
portables d'essai, de mesure et de surveillance utilisés Überwachungsgeräte für den Gebrauch in
dans des réseaux de distribution à basse tension Niederspannungs-Stromversorgungsnetzen
(IEC 61326-2-2:2020) (IEC 61326-2-2:2020)
This European Standard was approved by CENELEC on 2020-11-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61326-2-2:2021 E
European foreword
The text of document 65A/977/FDIS, future edition 3 of IEC 61326-2-2, prepared by SC 65A "System
aspects" of IEC/TC 65 "Industrial-process measurement, control and automation" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61326-2-2:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-12-04
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-06-04
document have to be withdrawn
This document supersedes EN 61326-2-2:2013 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 61326-2-2:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 61326-2-4:2020 NOTE Harmonized as EN IEC 61326-2-4:2021 (not modified)
IEC 61557-8:2014 NOTE Harmonized as EN 61557-8:2015 (not modified)
IEC 61557-9:2014 NOTE Harmonized as EN 61557-9:2015 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
The Annex ZA of EN IEC 61326-1:2021 applies with the following additions:
Publication Year Title EN/HD Year
IEC 61326-1 2020 Electrical equipment for measurement, EN IEC 61326-1 2021
control and laboratory use - EMC
requirements - Part 1: General
requirements
IEC 61557 series Electrical safety in low voltage distribution EN 61557 series
systems up to 1 000 V AC and 1 500 V DC
- Equipment for testing, measuring or
monitoring of protective measures - Part 1:
General requirements
IEC 61326-2-2
Edition 3.0 2020-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electrical equipment for measurement, control and laboratory use –
EMC requirements –
Part 2-2: Particular requirements – Test configurations, operational conditions
and performance criteria for portable testing, measuring and monitoring
equipment used in low-voltage distribution systems
Matériel électrique de mesure, de commande et de laboratoire –
Exigences relatives à la CEM –
Partie 2-2: Exigences particulières – Configurations d’essai, conditions de
fonctionnement et critères de performance des matériels portables d’essai,
de mesure et de surveillance utilisés dans des réseaux de distribution à basse
tension
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 17.220.20; 25.040.40; 33.100.20 ISBN 978-2-8322-8951-8
– 2 – IEC 61326-2-2:2020 © IEC 2020
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General . 6
5 EMC test plan . 6
5.1 General . 6
5.2 Configuration of EUT during testing . 6
5.3 Operation conditions of EUT during testing . 7
5.4 Specification of FUNCTIONAL PERFORMANCE . 8
5.5 Test description . 8
6 Immunity requirements . 8
6.1 Conditions during the tests. 8
6.2 Immunity test requirements . 8
6.3 Random aspects . 8
6.4 Performance criteria . 8
7 Emission requirements . 8
8 Test results and test report . 9
9 Instructions for use . 9
Annex A (normative) Immunity test requirements for PORTABLE TEST AND MEASUREMENT
EQUIPMENT powered by battery or from the circuit being measured . 10
Annex B (informative) Guide for analysis and assessment for electromagnetic
compatibility. 11
Bibliography . 12
Figure 101 – Test set-up for portable testing, measuring and monitoring equipment
based on IEC 61000-4-3 . 6
Figure 102 – Example of connection details for voltage measurements . 7
Figure 103 – Example of connection details for current measurements . 7
IEC 61326-2-2:2020 © IEC 2020 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICAL EQUIPMENT FOR MEASUREMENT,
CONTROL AND LABORATORY USE –
EMC REQUIREMENTS –
Part 2-2: Particular requirements –
Test configurations, operational conditions and
performance criteria for portable testing, measuring and
monitoring equipment used in low-voltage distribution systems
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
...