|
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.PHKNRPDJQHWQLKMagnetische Werkstoffe - Teil 6: Verfahren zur Messung der magnetischen Eigenschaften weichmagnetischer und pulverförmiger Werkstoffe bei Frequenzen im Bereich 20 Hz bis 200 kHz mit Hilfe von Ringproben (IEC 60404-6:2018)Matériaux magnétiques - Partie 6: Méthodes de mesure des propriétés magnétiques des matériaux métalliques et des matériaux en poudre, magnétiquement doux, aux fréquences comprises entre 20 Hz et 200 kHz, sur des éprouvettes en forme de tore (IEC 60404-6:2018)Magnetic materials - Part 6: Methods of measurement of the magnetic properties of magnetically soft metallic and powder materials at frequencies in the range 20 Hz to 200 kHz by the use of ring specimens (IEC 60404-6:2018)29.030Magnetni materialiMagnetic materials17.220.20Measurement of electrical and magnetic quantitiesICS:Ta slovenski standard je istoveten z:EN IEC 60404-6:2018SIST EN IEC 60404-6:2018en01-september-2018SIST EN IEC 60404-6:2018SLOVENSKI
STANDARDSIST EN 60404-6:20041DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN IEC 60404-6
July 2018 ICS 17.220.20; 29.030
Supersedes
EN 60404-6:2003
English Version
Magnetic materials - Part 6: Methods of measurement of the magnetic properties of magnetically soft metallic and powder materials at frequencies in the range 20 Hz to 100 kHz by the use of ring specimens (IEC 60404-6:2018)
Matériaux magnétiques - Partie 6: Méthodes de mesure des propriétés magnétiques des matériaux métalliques et des matériaux en poudre magnétiquement doux, aux fréquences comprises entre 20 Hz et 100 kHz, sur des éprouvettes en forme de tore (IEC 60404-6:2018)
Magnetische Werkstoffe - Teil 6: Verfahren zur Messung der magnetischen Eigenschaften weichmagnetischer und pulverförmiger Werkstoffe bei Frequenzen im Bereich 20 Hz bis 100 kHz mit Hilfe von Ringproben (IEC 60404-6:2018) This European Standard was approved by CENELEC on 2018-06-29. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23,
B-1040 Brussels © 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60404-6:2018 E SIST EN IEC 60404-6:2018
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2019-03-29 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021-06-29
This document supersedes EN 60404-6:2003.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60404-6:2018 was approved by CENELEC as a European Standard without any modification. SIST EN IEC 60404-6:2018
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1
Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2
Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-121 -
International Electrotechnical Vocabulary (IEV) -
Part 121: Electromagnetism - -
IEC 60050-221 -
International Electrotechnical Vocabulary (IEV) -
Chapter 221: Magnetic materials and components - -
IEC 60404-2 -
Magnetic materials -
Part 2: Methods of measurement of the magnetic properties of electrical steel sheet and strip by means of an Epstein frame EN 60404-2 -
IEC 60404-4 -
Magnetic materials -
Part 4: Methods of measurement of d.c. magnetic properties of magnetically soft materials EN 60404-4 -
IEC 60404-8-6 -
Magnetic materials -
Part 8-6: Specifications for individual materials - Soft magnetic metallic materials EN 60404-8-6 -
IEC 60404-8-9 -
Magnetic materials -
Part 8: Specification for individual materials - Section 9: Standard specification for sintered soft magnetic materials - -
IEC 62044-3 -
Cores made of soft magnetic materials - Measuring methods -
Part 3: Magnetic properties at high excitation level EN 62044-3 -
ISO/IEC Guide 98-3 -
Uncertainty of measurement -
Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) - -
IEC 60404-6 Edition 3.0 2018-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Magnetic materials –
Part 6: Methods of measurement of the magnetic properties of magnetically soft metallic and powder materials at frequencies in the range 20 Hz to 100 kHz by the use of ring specimens
Matériaux magnétiques –
Partie 6: Méthodes de mesure des propriétés magnétiques des matériaux métalliques et des matériaux en poudre magnétiquement doux, aux fréquences comprises entre 20 Hz et 100 kHz, sur des éprouvettes en forme de tore
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 17.220.20; 29.030
ISBN 978-2-8322-5716-6
– 2 –
IEC 60404-6:2018 © IEC 2018 CONTENTS FOREWORD . 4 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 7 4 General principles of measurement . 7 4.1 Principle of the ring method . 7 4.2 Test specimen . 7 4.3 Windings . 8 5 Temperature measurements . 9 6 Measurement of the relative amplitude permeability and the AC magnetization curve . 9 6.1 General . 9 6.2 Apparatus and connections . 9 6.3 Waveform of induced secondary voltage or magnetizing current . 10 6.4 Determination of characteristics . 11 6.4.1 Determination of the peak value of the magnetic field strength . 11 6.4.2 Determination of the peak value of the magnetic flux density . 12 6.4.3 Determination of the r.m.s. amplitude permeability and the relative amplitude permeability . 12 6.4.4 Determination of the AC magnetization curve . 13 7 Measurement of the specific total loss by the wattmeter method . 13 7.1 Principle of measurement. 13 7.2 Voltage measurement . 15 7.2.1 Average type voltmeter . 15 7.2.2 R.M.S. type voltmeter . 15 7.3 Power measurement . 15 7.4 Procedure for the measurement of the specific total loss . 15 7.5 Determination of the specific total loss . 15 8 Uncertainties . 16 9 Test report . 16 Annex A (informative)
Guidance on requirements for windings and instrumentation in order to minimise additional losses . 17 A.1 General . 17 A.2 Reduction of additional losses . 17 Annex B (informative)
Digital sampling technique for the determination of magnetic properties and numerical air flux compensation . 18 B.1 General . 18 B.2 Technical details and requirements . 18 B.3 Calibration aspects . 22 B.4 Numerical air flux compensation . 22 Annex C (informative)
Sinusoidal waveform control by digital means . 23 Bibliography . 24
Figure 1 – Circuit of the measurement apparatus . 10 SIST EN IEC 60404-6:2018
IEC 60404-6:2018 © IEC 2018 – 3 –
Figure 2 – Circuit of the conventional analogue wattmeter method (also representing the metrological principle of the digital wattmeter method) . 14 Figure 3 – The wattmeter method when connected with the digital sampling technique (example of circuit) . 14
– 4 –
IEC 60404-6:2018 © IEC 2018 INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
MAGNETIC MATERIALS –
Part 6: Methods of measurement of the magnetic properties of
magnetically soft metallic and powder materials at frequencies
in the range 20 Hz to 100 kHz by the use of ring specimens
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparen
...