EN 61534-1:2011/A11:2021

Powertrack systems - Part 1: General requirements

EN 61534-1:2011/A11:2021

Name:EN 61534-1:2011/A11:2021   Standard name:Powertrack systems - Part 1: General requirements
Standard number:EN 61534-1:2011/A11:2021   language:English language
Release Date:01-Jul-2021   technical committee:CLC/TC 213 - Cable management systems
Drafting committee:CLC/TC 213/WG 10 - Powertrack systems   ICS number:29.060.10 - Wires

SLOVENSKI STANDARD
01-september-2021
Sistemi napajalnih razvodnic - 1. del: Splošne zahteve - Dopolnilo A11
Powertrack systems - Part 1: General requirements
Stromschienensysteme - Teil 1: Allgemeine Anforderungen
Systèmes de conducteurs préfabriqués - Partie 1: Exigences générales
Ta slovenski standard je istoveten z: EN 61534-1:2011/A11:2021
ICS:
29.060.10 Žice Wires
29.120.10 Inštalacijske cevi za Conduits for electrical
električne namene purposes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 61534-1:2011/A11

NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2021
ICS 29.060.10; 29.120.10
English Version
Powertrack systems - Part 1: General requirements
Systèmes de conducteurs préfabriqués - Partie 1: Stromschienensysteme - Teil 1: Allgemeine Anforderungen
Exigences générales
This amendment A11 modifies the European Standard ; it was approved by CENELEC on 2021-04-29. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the status of a national
standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61534-1:2011/A11:2021 E

European foreword
This document (EN 61534-1:2011/A11:2021) has been prepared by CLC/TC 213 “Cable management
systems”.
The following dates are fixed:
• latest date by which this document has (dop) 2022-04-29
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2024-04-29
standards conflicting with this document
have to be withdrawn
This document amends EN 61534-1:2011/A2:2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this document.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
1 Modification to Clause 1, “Scope”
Add the following Note after the last dashed item under 1.2:
“NOTE Particular attention needs to be paid to installations rules when elements are installed which include
EMI suppression devices.”
2 Addition of new Annex H, “Routine Tests”
Add the following Annex H:

Annex H
(normative)
Routine tests
Routine tests are intended to detect faults in materials and/or in workmanship. They are carried out on every
new assembly after it has been assembled.
As a minimum, the following routine tests shall be carried out on each new assembly:
— inspection of the assembly and wiring if applicable,
— where applicable the operation of electrical devices,
— a dielectric test (Power-frequency withstand voltage) in accordance with Table 7, for the duration of at
least 1 s,
— continuity tests of the live conductors and their correct phasing,
— continuity tests of the protective circuits.
The tests may be carried out in any order.”
3 Addition of Annex ZA, “Normative references to international publications with
their corresponding European publications “
Add the following Annex ZA:

Annex ZA
(normative)
Normative references to international publications with their corresponding
European publications
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Replacement:
Publication Year Title EN/HD Year
IEC 60068-2-52 2017 Environmental testing - EN 60068-2-52 2018
Part 2: Tests - Test Kb: Salt mist, cyclic (sodium
chloride solution)
IEC
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27