|
SLOVENSKI STANDARD
01-oktober-2021
Nadomešča:
SIST EN 60695-4:2012
Preskušanje požarne ogroženosti - 4. del: Izrazje v zvezi s požarnimi preskusi
elektrotehničnih proizvodov (IEC 60695-4:2021)
Fire hazard testing - Part 4: Terminology concerning fire tests for electrotechnical
products (IEC 60695-4:2021)
Prüfungen zur Beurteilung der Brandgefahr - Teil 4: Terminologie der Brandprüfungen
elektrotechnischer Produkte (IEC 60695-4:2021)
Essais relatifs aux risques du feu - Partie 4: Terminologie relative aux essais au feu pour
les produits électrotechniques (IEC 60695-4:2021)
Ta slovenski standard je istoveten z: EN IEC 60695-4:2021
ICS:
01.040.13 Okolje. Varovanje zdravja. Environment. Health
Varnost (Slovarji) protection. Safety
(Vocabularies)
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.020 Elektrotehnika na splošno Electrical engineering in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60695-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2021
ICS 01.040.13; 29.020 Supersedes EN 60695-4:2012 and all of its amendments
and corrigenda (if any)
English Version
Fire hazard testing - Part 4: Terminology concerning fire tests for
electrotechnical products
(IEC 60695-4:2021)
Essais relatifs aux risques du feu - Partie 4: Terminologie Prüfungen zur Beurteilung der Brandgefahr - Teil 4:
relative aux essais au feu pour les produits Terminologie der Brandprüfungen elektrotechnischer
électrotechniques Produkte
(IEC 60695-4:2021) (IEC 60695-4:2021)
This European Standard was approved by CENELEC on 2021-07-28. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60695-4:2021 E
European foreword
The text of document 89/1462/CDV, future edition 5 of IEC 60695-4, prepared by IEC/TC 89 “Fire
hazard testing” was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022–04–28
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024–07–28
document have to be withdrawn
This document supersedes EN 60695-4:2012 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60695-4:2021 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050 series International Electrotechnical Vocabulary - -
IEC Guide 104 - The preparation of safety publications and - -
the use of basic safety publications and
group safety publications
ISO 13943 2017 Fire safety - Vocabulary EN ISO 13943 2017
ISO/IEC Guide 51 - Safety aspects - Guidelines for their - -
inclusion in standards
IEC 60695-4
Edition 5.0 2021-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fire hazard testing –
Part 4: Terminology concerning fire tests for electrotechnical products
Essais relatifs aux risques du feu –
Partie 4: Terminologie relative aux essais au feu pour les produits
électrotechniques
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 01.040.13; 29.020 ISBN 978-2-8322-9906-7
– 2 – IEC 60695-4:2021 © IEC 2021
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
3.1 Use of the term “item” . 5
3.2 Other terms and definitions . 5
IEC 60695-4:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIRE HAZARD TESTING –
Part 4: Terminology concerning fire tests
for electrotechnical products
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whats
...