|
SLOVENSKI STANDARD
01-november-2021
Sistemi napajalnih razvodnic - 21. del: Posebne zahteve za sisteme napajalnih
razvodnic, predvidene za stensko in stropno montažo - Dopolnilo A11
Powertrack systems - Part 21: Particular requirements for powertrack systems intended
for wall and ceiling mounting
Stromschienensysteme - Teil 21: Besondere Anforderungen für Stromschienensysteme
für Wand und Decke
Systèmes de conducteurs préfabriqués - Partie 21: Exigences particulières pour les
systèmes de conducteurs préfabriqués destinés au montage sur des murs et des
plafonds
Ta slovenski standard je istoveten z: EN 61534-21:2014/A11:2021
ICS:
29.060.10 Žice Wires
29.120.20 Spojni elementi Connecting devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 61534-21:2014/A11
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2021
ICS 29.060.10; 29.120.20
English Version
Powertrack systems - Part 21: Particular requirements for
powertrack systems intended for wall and ceiling mounting
Systèmes de conducteurs préfabriqués - Partie 21: Stromschienensysteme - Teil 21: Besondere Anforderungen
Exigences particulières pour les systèmes de conducteurs für Stromschienensysteme für Wand und Decke
préfabriqués destinés au montage sur des murs et des
plafonds
This amendment A11 modifies the European Standard ; it was approved by CENELEC on 2020-12-22. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the status of a national
standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61534-21:2014/A11:2021 E
European foreword
This document (EN 61534-21:2014/A11:2021) has been prepared by CLC/TC 213 “Cable management
systems”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2022-03-24
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2024-09-24
conflicting with this document have to be
withdrawn
This document amends EN 61534-21:2014/A1:2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZZ, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
1 Modification to Clause 1, “Scope”
Add the following Note after the last dashed item under 1.2:
“
NOTE Particular attention needs to be paid to installations rules when elements are installed which include EMI
suppression devices.”
2 Addition of new Annex H, “Routine Tests”
Add the following Annex H:
“
Annex H
(normative)
Routine tests
Routine tests are intended to detect faults in materials and/or in workmanship. They are carried out on every
new assembly after it has been assembled.
As a minimum, the following routine tests shall be carried out on each new assembly:
— Inspection of the assembly and wiring if applicable,
— Where applicable the operation of electrical devices,
— A dielectric test (Power-frequency withstand voltage) in accordance with Table 7, for the duration of at
least 1 s,
— Continuity tests of the live conductors and their correct phasing,
— Continuity tests of the protective circuits.
The tests may be carried out
...