EN IEC 60695-9-2:2021

Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods

EN IEC 60695-9-2:2021

Name:EN IEC 60695-9-2:2021   Standard name:Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods
Standard number:EN IEC 60695-9-2:2021   language:English language
Release Date:30-Sep-2021   technical committee:CLC/SR 89 - Fire hazard testing
Drafting committee:IEC/TC 89 - IEC_TC_89   ICS number:13.220.40 - Ignitability and burning behaviour of materials and products

SLOVENSKI STANDARD
01-december-2021
Nadomešča:
SIST EN 60695-9-2:2014
Preskušanje požarne ogroženosti - 9-2. del: Površinsko širjenje plamena - Pregled
in primernost preskusnih metod (IEC 60695-9-2:2021)
Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test
methods (IEC 60695-9-2:2021)
Prüfungen zur Beurteilung der Brandgefahr - Teil 9-2: Flammenausbreitung auf
Oberflächen - Zusammenfassung und Anwendbarkeit der Prüfverfahren (IEC 60695-9-
2:2021)
Essais relatifs aux risques du feu - Partie 9-2: Propagation des flammes en surface -
Résumé et pertinence des méthodes d'essai (IEC 60695-9-2:2021)
Ta slovenski standard je istoveten z: EN IEC 60695-9-2:2021
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.020 Elektrotehnika na splošno Electrical engineering in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60695-9-2

NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2021
ICS 13.220.40; 29.020 Supersedes EN 60695-9-2:2014 and all of its
amendments and corrigenda (if any)
English Version
Fire hazard testing - Part 9-2: Surface spread of flame -
Summary and relevance of test methods
(IEC 60695-9-2:2021)
Essais relatifs aux risques du feu - Partie 9-2: Propagation Prüfungen zur Beurteilung der Brandgefahr - Teil 9-2:
des flammes en surface - Résumé et pertinence des Flammenausbreitung auf Oberflächen - Zusammenfassung
méthodes d'essai und Anwendbarkeit der Prüfverfahren
(IEC 60695-9-2:2021) (IEC 60695-9-2:2021)
This European Standard was approved by CENELEC on 2021-09-29. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60695-9-2:2021 E

European foreword
The text of document 89/1469/CDV, future edition 2 of IEC 60695-9-2, prepared by IEC/TC 89 “Fire
hazard testing” was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
latest date by which the document has to be implemented at national (dop) 2022–06–29

level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024–09–29
document have to be withdrawn
This document supersedes EN 60695-9-2:2014 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60695-9-2:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60695-1-11 NOTE Harmonized as EN 60695-1-11
IEC 60695-1-12 NOTE Harmonized as EN IEC 60695-1-12
IEC 60695-11-10 NOTE Harmonized as EN 60695-11-10
IEC 60695-11-20 NOTE Harmonized as EN 60695-11-20
IEC 60695-11-3 NOTE Harmonized as EN 60695-11-3
IEC 60684-2:2011 NOTE Harmonized as EN 60684-2:2011 (not modified)
IEC 60332-1 NOTE Harmonized as HD 405.1 S1
IEC 60332-2 NOTE Harmonized as HD 405.2 S1
ISO 3582 NOTE Harmonized as EN ISO 3582
ISO 9773 NOTE Harmonized as EN ISO 9773
ISO 11925-2 NOTE Harmonized as EN ISO 11925-2
IEC 60695-8-1 NOTE Harmonized as EN 60695-8-1
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60695-1-10 - Fire hazard testing - Part 1–10: Guidance EN 60695-1-10 -
for assessing the fire hazard of
electrotechnical products - General
guidelines
IEC 60695-4 2012 Fire hazard testing - Part 4: Terminology EN 60695-4 2012
concerning fire tests for electrotechnical
products
IEC 60695-9-1 - Fire hazard testing - Part 9–1: Surface EN 60695-9-1 -
spread of flame - General guidance
IEC Guide 104 - The preparation of safety publications and - -
the use of basic safety publications and
group safety publications
ISO/IEC Guide 51 - Safety aspects - Guidelines for their -
inclusion in standards
ISO 13943 2017 Fire Safety - Vocabulary EN ISO 13943 2017
ISO 19706 2011 Guidelines for assessing the fire threat to - -
people
IEC 60695-9-2
Edition 2.0 2021-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
HORIZONTAL PUBLICATION
PUBLICATION HORIZONTALE
Fire hazard testing –
Part 9-2: Surface spread of flame – Summary and relevance of test methods

Essais relatifs aux risques du feu –

Partie 9-2: Propagation des flammes en surface – Résumé et pertinence

des méthodes d'essai
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.220.40; 29.020 ISBN 978-2-8322-9997-5

– 2 – IEC 60695-9-2:2021 © IEC 2021
CONTENTS
FOREWORD . 3
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 Summary of published test methods . 12
4.1 General . 12
4.2 The physical fire model . 12
4.3 Small-scale fire tests. 14
4.3.1 Horizontal and vertical 50 W and 500 W flame tests – IEC 60695-11-10
and IEC 60695-11-20 . 14
4.3.2 Fire hazard testing – Part 11-21: Test flames – 500 W vertical flame
test method for tubular polymeric materials – IEC TS 60695-11-21 [5] . 14
4.3.3 Flexible insulating sleeving – Part 2: Methods of test, Clause 26: Flame
propagation tests – IEC 60684-2:2011 [7], Clause 26 . 15
4.3.4 Vertical burning test for cables – IEC 60332-1 [9] . 16
4.3.5 Vertical burning test for cables – IEC 60332-2 [10] . 17
4.3.6 Flexible cellular polymeric materials – Laboratory assessment of horizontal
burning characteristics of small specimens subjected to a small flame –
ISO 3582 [11] . 18
4.3.7 Horizontal burning rate for road vehicle materials – ISO 3795 [12]. . 19
4.3.8 Cellular plastics – Determination of horizontal burning characteristics of
small specimens subjected to a small flame – ISO 9772 [13] . 19
4.3.9 Plastics – Determination of burning behaviour of thin flexible vertical
specimens in contact with a small-flame ignition source – ISO 9773 [15] . 20
4.3.10 Fire propagation apparatus – ISO 12136 [16] . 21
4.3.11 Plastics – Vertical flame spread determination for film and sheet –
ISO 12992 [27] . 23
4.3.12 Vertical burning test for aircraft materials – FAR 25 [29] . 23
4.4 Medium and intermediate-scale fire tests . 24
4.4.1 Lateral flame spread on building and transport products – ISO 5658-2 [30] . 24
4.4.2 Intermediate-scale fire test of vertical flame spread – ISO 5658-4 [33]. 25
4.4.3 Plastics – Reaction to fire – Test method for flame spread and combustion
product release from vertically oriented specimens – ISO 21367 [35] . 26
4.5 Intermediate and large-scale fire tests for cables . 26
4.5.1 General . 26
4.5.2 Vertical burning tests for cables (ladder tests) . 27
4.5.3 Vertical burning test for cables – NF C 32-070 [60] . 31
4.6 Real-scale fire tests for cables . 31
4.6.1 Standard for test for flame propagation height of electrical and optical-
fiber cables installed vertically in shafts – UL 1666 [61] . 31
4.6.2 Horizontal flame spread test for cables – EN 50289-4-11 [62] . 32
5 Overview of methods and relevance of data . 33
Bibliography . 38

Table 1 – Characteristics of fire stages (ISO 19706:2011) . 13
a)
Table 2 – Summary and comparison of IEC 60332 vertical ladder test methods [37] . 28
Table 3 – Summary and comparison of non-IEC vertical ladder test methods . 29
Table 4 – Overview of flame spread methods . 34

IEC 60695-9-2:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIRE HAZARD TESTING –
Part 9-2: Surface spread of flame –
Summary and relevance of test methods

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27