|
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.LWL-Sensoren - Teil 1: Fachgrundspezifikation (IEC 61757:2018)Capteurs a fibres optiques - Partie 1: Spécification générique (IEC 61757:2018)Fibre optic sensors - Part 1: Generic specification (IEC 61757:2018)33.180.99YODNQDOther fibre optic equipmentICS:Ta slovenski standard je istoveten z:EN IEC 61757:2018SIST EN IEC 61757-1:2018en01-december-2018SIST EN IEC 61757-1:2018SLOVENSKI
STANDARDSIST EN 61757-1:20121DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN IEC 61757
October 2018 ICS 33.180.99
Supersedes
EN 61757-1:2012
English Version
Fibre optic sensors - Generic specification (IEC 61757:2018)
Capteurs à fibres optiques - Spécification générique (IEC 61757:2018)
LWL-Sensoren - Fachgrundspezifikation (IEC 61757:2018) This European Standard was approved by CENELEC on 2018-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23,
B-1040 Brussels © 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61757:2018 E SIST EN IEC 61757-1:2018
This document supersedes EN 61757-1:2012. This document constitutes a technical revision including the following technical changes with respect to EN 61757-1:2012:
a. change of the document number due to a new structure of the fibre optic sensor standard series; b. update of the normative references and bibliography; c. revision of Annex A. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 61757:2018 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60654-4 NOTE Harmonized as EN 60654-4. IEC 60721-1 NOTE Harmonized as EN 60721-1. SIST EN IEC 61757-1:2018
Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1
Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2
Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.
Publication Year Title EN/HD Year IEC 60050 series
International Electrotechnical Vocabulary
- series
IEC 60060-1 -
High-voltage test techniques -- Part 1: General definitions and test requirements EN 60060-1 -
IEC 60068-1 -
Environmental testing -- Part 1: General and guidance EN 60068-1 -
IEC 60068-2-1 -
Environmental testing - Part 2-1: Tests - Test A: Cold EN 60068-2-1 -
IEC 60068-2-2 -
Environmental testing - Part 2-2: Tests - Test B: Dry heat EN 60068-2-2 -
IEC 60068-2-5 -
Environmental testing – Part 2-5: Tests – Test Sa: Simulated solar radiation at ground level and guidance for solar radiation testing EN IEC 60068-2-5 -
IEC 60068-2-6 -
Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) EN 60068-2-6 -
IEC 60068-2-10 -
Environmental testing - Part 2-10: Tests - Test J and guidance: Mould growth EN 60068-2-10 -
IEC 60068-2-11 -
Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist EN 60068-2-11 -
IEC 60068-2-13 -
Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure EN 60068-2-13 -
IEC 60068-2-14 -
Environmental testing - Part 2-14: Tests - Test N: Change of temperature EN 60068-2-14 -
IEC 60068-2-27 -
Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock EN 60068-2-27 -
IEC 60068-2-30 -
Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) EN 60068-2-30 -
Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections EN 60068-2-42 -
IEC 60068-2-43 -
Environmental testing - Part 2-43: Tests - Test Kd: Hydrogen sulphide test for contacts and connections EN 60068-2-43 -
IEC 60068-2-78 -
Environmental testing -- Part 2-78: Tests - Test Cab: Damp heat, steady state EN 60068-2-78 -
IEC 60079-28 -
Explosive atmospheres -- Part 28: Protection of equipment and transmission systems using optical radiation EN 60079-28 -
IEC 60529 -
Degrees of protection provided by enclosures (IP Code) - -
IEC 60793-1-20 -
Optical fibres - Part 1-20: Measurement methods and test procedures - Fibre geometry EN 60793-1-20 -
IEC 60793-1-21 -
Optical fibres -- Part 1-21: Measurement methods and test procedures - Coating geometry EN 60793-1-21 -
IEC 60793-1-31 -
Optical fibres -- Part 1-31: Measurement methods and test procedures - Tensile strength EN 60793-1-31 -
IEC 60793-1-32 -
Optical fibres -- Part 1-32: Measurement methods and test procedures - Coating strippability EN 60793-1-32 -
IEC 60793-1-47 -
Optical fibres – Part 1-47: Measurement methods and test procedures – Macrobending loss EN IEC 60793-1-47 -
IEC 60793-1-54 -
Optical fibres – Part 1-54: Measurement methods and test procedures – Gamma irradiation EN IEC 60793-1-54 -
IEC 60794-1-21 -
Optical fibre cables - Part 1-21: Generic specification - Basic optical cable test procedures - Mechanical tests methods EN 60794-1-21 -
IEC 60825-1 -
Safety of laser products -- Part 1: Equipment classification and requirements EN 60825-1 -
IEC 60874-1 -
Fibre optic interconnecting devices and passive components - Connectors for optical fibres and cables -- Part 1: Generic specification EN 60874-1 -
IEC 61000-4-2 -
Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test EN 61000-4-2 -
IEC 61000-4-3 -
Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test - -
Electromagnetic compatibility (EMC) -- Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test EN 61000-4-4 -
IEC 61000-4-5 -
Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test EN 61000-4-5 -
IEC 61300 series
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures
EN 61300 series
IEC 61300-2-1 -
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-1: Tests - Vibration (sinusoidal) EN 61300-2-1 -
IEC 61300-2-9 -
Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-9: Tests – Shock EN 61300-2-9 -
IEC 61300-2-18 -
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-18: Tests - Dry heat - High temperature endurance EN 61300-2-18 -
IEC 61300-2-22 -
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-22: Tests - Change of temperature EN 61300-2-22 -
IEC 61300-2-34 -
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-34: Tests - Resistance to solvents and contaminating fluids of interconnecting components and closures EN 61300-2-34 -
IEC 61300-2-46 -
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-46: Tests - Damp heat cyclic EN 61300-2-46 -
IEC 61300-3-35 -
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-35: Examinations and measurements - Visual inspection of fibre optic connectors and fibre-stub transceivers EN 61300-3-35 -
IEC 61753 series
Fibre optic interconnecting devices and passive components performance standard
EN 61753 series
IEC/TR 61931 -
Fibre optic - Terminology - -
IEC/TR 62222 -
Fire performance of communication cables installed in buildings - -
IEC/TR 62283 -
Optical fibres - Guidance for nuclear radiation tests - -
Fibre optic interconnecting devices and passive components - Part 01: Fibre optic connector cleaning methods - -
ISO/IEC Guide 99 -
International vocabulary of metrology - Basic and general concepts and associated terms (VIM) - -
IEC 61757 Edition 1.0 2018-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic sensors – Generic specification
Capteurs à fibres optiques – Spécification générique
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 33.180.99
ISBN 978-2-8322-5303-8
– 2 – IEC 61757:2018 © IEC 2018 CONTENTS FOREWORD . 5 INTRODUCTION . 7 1 Scope . 8 2 Normative references . 8 3 Terms and definitions . 10 4 Quality assurance . 17 5 Test and measurement procedures . 17 5.1 General . 17 5.2 Standard conditions for testing . 17 5.3 Test and measurement equipment requirements . 18 5.4 Visual inspection . 18 5.5 Dimensions . 18 5.6 Metrological properties. 18 5.6.1 General . 18 5.6.2 Metrological parameters . 19 5.7 Optical tests . 19 5.7.1 General . 19 5.7.2 Optical power . 19 5.7.3 Nominal wavelength and appropriate spectral characteristics . 19 5.7.4 State of polarization . 19 5.7.5 Fibre connector performance . 19 5.8 Electrical tests . 19 5.8.1 General . 19 5.8.2 Parameters and test procedures . 20 5.8.3 Voltage stress. 20 5.9 Mechanical tests . 20 5.9.1 General . 20 5.9.2 Parameters and test procedures . 20 5.10 Climatic and environmental tests . 21 5.10.1 Ge
...