|
SLOVENSKI STANDARD
01-januar-2019
1DGRPHãþD
SIST HD 597 S1:2001
6NORSQLNRQGHQ]DWRUMLLQNRQGHQ]DWRUVNLGHOLOQLNLGHO (QRVPHUQLLQL]PHQLþQL
HQRID]QLNRQGHQ]DWRUVNLGHOLOQLNL ,(&
Coupling capacitors and capacitor dividers - Part 4: DC and AC single-phase capacitor
dividers (IEC 60358-4:2018)
Ta slovenski standard je istoveten z: EN IEC 60358-4:2018
ICS:
31.060.99 Drugi kondenzatorji Other capacitors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60358-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2018
ICS 29.120.99; 29.240.99; 31.060.70 Supersedes HD 597 S1:1992 (partially)
English Version
Coupling capacitors and capacitor dividers - Part 4: DC and AC
single-phase capacitor dividers
(IEC 60358-4:2018)
Condensateurs de couplage et diviseurs capacitifs - Partie Kopplungskondensatoren und kapazitive Teiler - Teil 4:
4: Diviseurs capacitifs monophasés pour courant alternatif Einphasen-Spannungsteiler-Kondensatoren für Wechsel-
ou pour courant continu oder Gleichstrom
(IEC 60358-4:2018) (IEC 60358-4:2018)
This European Standard was approved by CENELEC on 2018-08-07. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60358-4:2018 E
European foreword
The text of document 33/616/FDIS, future edition 1 of IEC 60358-4, prepared by IEC/TC 33 "Power
capacitors and their applications" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60358-4:2018.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-05-23
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2021-11-23
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document supersedes HD 597 S1:1992 (partially).
This European Standard is to be used in conjunction with the latest edition of EN 60358-1 and its
amendments. It was established on the basis of the first edition (2012) of that standard.
This Part 4 supplements or modifies the corresponding clauses in EN 60358-1.
When a particular subclause of Part 1 is not mentioned in this Part 4, that subclause applies as far as
is reasonable. Where this Part 4 states “addition” or “replacement”, the relevant text in Part 1 is to be
adapted accordingly.
For additional clauses, subclauses, figures, tables or annexes, the following numbering system is
used:
— subclauses, tables and figures which are additional to those in Part 1 are numbered starting
from 400;
— additional tables and annexes are lettered AA, BB etc.;
— as the notes are integrated into the clauses, their numbering starts from 1 as usual.
Endorsement notice
The text of the International Standard IEC 60358-4:2018 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60358-1 2012 Coupling capacitors and capacitor dividers EN 60358-1 2012
- Part 1: General rules
+ Corrigendum 1 2013 + AC 2013
IEC 60358-4
Edition 1.0 2018-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Coupling capacitors and capacitor dividers –
Part 4: DC or AC single-phase capacitor dividers
Condensateurs de couplage et diviseurs capacitifs –
Partie 4: Diviseurs capacitifs monophasés pour courant alternatif ou pour
courant continu
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.120.99; 29.240.99; 31.060.70 ISBN 978-2-8322-5863-7
– 2 – IEC 60358-4:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Service conditions . 8
5 Ratings . 8
6 Design requirements . 8
7 Test conditions . 10
8 Classification of tests. 10
9 Routine tests . 10
10 Type tests . 12
11 Special tests . 12
12 Marking . 12
Annex 4A (informative) Example of diagram of dividers. 13
Figure 400 – Connection for voltage test on low voltage part . 11
Figure 401 – Different types of dividers . 12
Figure 4A.400 – Example of diagram of dividers . 13
IEC 60358-4:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
COUPLING CAPACITORS AND CAPACITOR DIVIDERS –
Part 4: DC or AC single-phase capacitor dividers
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60358-4 has been prepared by IEC technical committee 33: Power
capacitors and their applications.
The text of this International Standard is based on the following documents:
FDIS Report on voting
33/616/FDIS 33/617/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all Parts in the IEC 60358 series, published under the general title Coupling
capacitors and capacitor dividers, can be found on the IEC website.
– 4 – IEC 60358-4:2018 © IEC 2018
Parts 2 through 4 of IEC 60358 are to be used in conjunction with the latest edition of
IEC 60358-1 and its amendments. They were established on the basis of the first edition
(2012) of that standard.
Parts 2 through 4 of IEC 60358 supplement or modify the corresponding clauses in
IEC 60358-1.
When a particular subclause of Part 1 is not mentioned in Parts 2 through 4, that subclause
applies as far as is reasonable. When this document states “addition”, “modification” or
“replacement”, the relevant text in Part 1 is to be adapted accordingly.
For additional clauses, subclauses, figures, tables or annexes, the following numbering
system is used:
• subclauses, tables and figures which are additional to those in Part 1 are numbered
starting from 200 for Part 2, 300 for Part 3 and 400 for Part 4;
• additional tables or annexes in the remaining Parts are lettered 2A, 2B, 3A, 3B, etc.
• as the notes are integrated into the clauses, their numbering are starting from 1 as usual.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the
...