|
SLOVENSKI STANDARD
01-februar-2022
Nadomešča:
SIST EN 60695-2-10:2013
Preskušanje požarne ogroženosti - 2-10. del: Preskusne metode z žarilno žico -
Aparat z žarilno žico in postopek splošnega preskusa (IEC 60695-2-10:2021)
Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire
apparatus and common test procedure (IEC 60695-2-10:2021)
Prüfungen zur Beurteilung der Brandgefahr - Teil 2-10: Prüfverfahren mit dem Glühdraht
- Glühdrahtprüfeinrichtung und allgemeines Prüfverfahren (IEC 60695-2-10:2021)
Essais relatifs aux risques du feu - Partie 2-10: Essais au fil incandescent/chauffant -
Appareillage et méthode commune d'essai (IEC 60695-2-10:2021)
Ta slovenski standard je istoveten z: EN IEC 60695-2-10:2021
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.020 Elektrotehnika na splošno Electrical engineering in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60695-2-10
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2021
ICS 13.220.40; 29.020 Supersedes EN 60695-2-10:2013 and all of its
amendments and corrigenda (if any)
English Version
Fire hazard testing - Part 2-10: Glowing/hot-wire based test
methods - Glow-wire apparatus and common test procedure
(IEC 60695-2-10:2021)
Essais relatifs aux risques du feu - Partie 2-10: Essais au fil Prüfungen zur Beurteilung der Brandgefahr - Teil 2-10:
incandescent/chauffant - Appareillage et méthode Prüfverfahren mit dem Glühdraht - Glühdrahtprüfeinrichtung
commune d'essai und allgemeines Prüfverfahren
(IEC 60695-2-10:2021) (IEC 60695-2-10:2021)
This European Standard was approved by CENELEC on 2021-12-02. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60695-2-10:2021 E
European foreword
The text of document 89/1535/FDIS, future edition 3 of IEC 60695-2-10, prepared by IEC/TC 89 “Fire
hazard testing” was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022–09–02
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024–12–02
document have to be withdrawn
This document supersedes EN 60695-2-10:2013 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60695-2-10:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60695-1-10 NOTE Harmonized as EN 60695-1-10
IEC 60695-1-11 NOTE Harmonized as EN 60695-1-11
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60584-1 - Thermocouples - Part 1: EMF EN 60584-1 -
specifications and tolerances
IEC 60695-2-11 - Fire hazard testing - Part 2–11: EN IEC 60695-2-11 -
Glowing/hot-wire based test methods -
Glow-wire flammability test method for end
products (GWEPT)
IEC 60695-2-12 - Fire hazard testing - Part 2–12: EN IEC 60695-2-12 -
Glowing/hot-wire based test methods -
Glow-wire flammability index (GWFI) test
method for materials
IEC 60695-2-13 - Fire hazard testing - Part 2–13: EN IEC 60695-2-13 -
Glowing/hot-wire based test methods -
Glow-wire ignition temperature (GWIT) test
method for materials
ISO 4046-4 2016 Paper, board, pulps and related terms - - -
Vocabulary - Part 4: Paper and board
grades and converted products
ISO 13943 2017 Fire safety - Vocabulary EN ISO 13943 2017
IEC 60695-2-10
Edition 3.0 2021-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
HORIZONTAL PUBLICATION
PUBLICATION HORIZONTALE
Fire hazard testing –
Part 2-10: Glowing/hot-wire based test methods – Glow-wire apparatus and
common test procedure
Essais relatifs aux risques du feu –
Partie 2-10: Essais au fil incandescent/chauffant – Appareillage et méthode
commune d’essai
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.220.40; 29.020 ISBN 978-2-8322-1010-9
– 2 – IEC 60695-2-10:2021 © IEC 2021
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 Description of the test apparatus . 10
4.1 Glow-wire. 10
4.2 Electrical circuit of the glow-wire apparatus . 11
4.3 Temperature measuring system . 12
4.4 Specified layer . 13
4.5 Test chamber . 14
4.6 Timing device . 14
5 Verification of the apparatus . 15
5.1 Verification of the glow-wire tip . 15
5.2 Verification of the temperature measuring system . 15
6 Conditioning . 15
7 Common test procedure . 15
7.1 Test specimen support . 15
7.2 Glow-wire temperature . 16
7.3 Application of the glow-wire . 16
8 General test observations and evaluations of test results . 16
Annex A (normative) Requirements for "ignition" and "flaming" observations . 17
A.1 General . 17
A.2 Examples of ignition and non-ignition . 17
Annex B (informative) Guidance on the verification procedure of the glow-wire
temperature measuring system by the heating current . 19
B.1 Objective . 19
B.2 Preparation . 19
B.3 Verification procedure . 19
B.3.1 Observation and measurement . 19
B.3.2 Correlation chart . 19
B.3.3 Frequency of revising the correlation chart . 20
Annex C (informative) Supplement – Times and durations, and examples of
evaluations . 21
C.1 Times and durations (in accordance with Clause 3) . 21
C.2 Examples of evaluations . 21
Bibliography . 23
Figure 1 – Glow-wire and position of thermocouple . 11
Figure 2 – Electrical circuit of the glow-wire apparatus . 12
Figure 3 – Test apparatus examples . 14
Figure A.1 – Example of a brightly shining flame . 17
Figure A.2 – Example of a blue corona at the glow-wire tip . 18
Figure A.3 – Example of ionized gases in the form of a tail near the glow wire tip . 18
IEC 60695-2-10:2021 © IEC 2021 – 3 –
Figure B.1 – Correlation curve between the heating current and the glow-wire
temperature (example) . 20
Figure C.1 – Times and durations (Example: ignition occurs at 5 s and extinguishing
occurs at 50 s) . 21
Figure C.2 – Evaluation scheme with examples . 22
– 4 – IEC 60695-2-10:2021 © IEC 2021
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIRE HAZARD TESTING –
Part 2-10: Glowing/hot-wire based test methods –
Glow-wire apparatus and common test procedure
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also pa
...