Structure design of the wind measuring tower
(1) The wind measuring tower shall be a guyed tower with an equilateral triangular structure with the same top and bottom of the tower 70 meters. is 0.5 meters and the side length of the 100 and 120 meter towers is 0.5 meters. The side length of the wind measuring tower is 1 meter;
(2) The bottom of the wind measuring tower. shall be designed as a conical hinged structure;
(3) The wind measuring tower shall be fixed by three-sided multi-layer guy wires, the number of guy wire layers is determined according to relevant standards;
(4) Install a platform at the bottom of the tower 7 meters above the ground, with a bearing capacity of at least 300 kg. Equipment such as sensors and solar panels will be installed above the platform. The platform was built primarily to facilitate manual data collection and to ensure securityity of the wind tower observation instruments. An iron door should be installed at the bottom of the platform, and the iron door can be closed with an iron lock.
(5) The wind measuring tower must be designed and installed with a crossbar to erect weather sensors. In accordance with the requirement that the length of the crosshead should be more than three times the diameter of the airspeed tower, the length of the crosshead of the 70-meter tower should be 1.75 meters, and that of the towers should be 100 and 120 meters. the meter towers must measure 3.5 meters. The crosshead must be stable and reliable and must meet the standardization and stability requirements for the installation, mounting and observation of instruments and equipment.
(6) The installation height and number of layers of the crosshead are determined according to the type of wind measuring tower: the crosshead of the 70 meter tower is divided into 4 layers, respectively at 10, 30, 50 and 70 meters; the 100 meter tower The transverse arm is divided into 5 floors, located respectively at 10, 30, 50, 70 and 100 meters, the transverse arm of the 120 meter tower is divided into 7 floors; , located at 1.5, 10, 30, 50, 70, 100 and 120 meters.
(7) The horizontal arm used to erect the weather sensors on the wind measurement tower must be telescopic to facilitate the installation and maintenance of the weather sensors.
(8) The verticality of the tower must be ≤1/1000.
For more information on drafting and producing engineering/service/purchasing tender documents to improve the bid winning rate, you can click on the official website customer service at the bottom for free consultation: https://bid. lcyff.com/#/?source= bdzd
(1) The wind measurement tower shall be an equilateral triangular steel structure guyed tower with the same top and bottom.The side length of 70 meters. the tower is 0.5 meters, and the side length of the 100 and 120 meter towers is 1 meter.
(2) The bottom of the wind measuring tower must be designed as a conical hinged structure.
(3) The wind measuring tower shall be fixed with multi-layer and three-sided guy wires, and the number of guy wire layers is determined in accordance with relevant standards.
(4) Install a platform at the bottom of the tower 7 meters above the ground, with a bearing capacity of at least 300 kg. Equipment such as sensors and solar panels will be installed above the platform. The platform was erected primarily to facilitate manual data collection and to ensure the safety of the wind tower's observation instruments. An iron door should be installed at the bottom of the platform, and the iron door can be closed with an iron lock.
(5) The wind measurement tower must be designed andstalled with a crossbar to erect weather sensors. In accordance with the requirement that the length of the cross arm is more than three times the diameter of the wind measuring tower, the length of the cross arm of the 70 meter tower is 1.75 meters, 100 and 120 meters. The length of the transverse arm of the tower extending from the tower body is 3.5 meters. The crosshead must be stable and reliable and must meet the standardization and stability requirements for the installation, mounting and observation of instruments and equipment.
(6) The installation height and number of layers of the crosshead are determined according to the type of wind measuring tower: the crosshead of the 70 meter tower is divided into 4 layers, respectively at 10, 30, 50 and 70 meters. The transverse arm of the 100-meter tower is divided into 5 floors, at 10, 30, 50, 70 and 100 meters respectively. The transverse arm of the 120 meter tower is divided into 7 levelses, respectively at 1.5, 10, 30, 50, 70, 100 and 120 meters.
(7) The horizontal arm used to erect the weather sensors on the wind measurement tower must be telescopic to facilitate the installation and maintenance of the weather sensors.
(8) The verticality of the tower must be ≤1/1000.
For more information on drafting and producing engineering/service/purchasing tender documents to improve the bid winning rate, you can click on the official website customer service at the bottom for free consultation: https://bid. lcyff.com/#/?source=bdzd