How to convert a generator or car engine into a wind turbine

Introduction How to transform a generator or car engine into a wind turbine? Because you are powered by wind energy, it is obviously not possible to use wind energy to drive the car's motor and then use the motor to drive the rotor or coil to produce electricity.

How to convert a generator or car engine into a wind turbine

Since you are powered by wind, it is obviously impossible and unrealistic to use wind power to drive a car motor and then use the motor to drive the rotor or coil to produce electricity. Because it is impossible for the engine to directly produce electricity, just like a car must rely on the engine to drive the generator to produce electricity.

It is possible to use a car generator. The car generator is usually connected to the engine via a pulley and belt to convert the mechanical energy produced by the engine into electrical energy. this method and use a pulley and straps to connect your generator to the wind output device. More specifically, you just need a belt of appropriate length. Simply connect the two together like a bicycle chain so they can spin together.

Ifyou want to increase the gear ratio, for example 1:2 (wind blades rotate once, generator rotates twice), you just need to add another belt and a pair of gears (teeth) with a large transmission ratio. Count one large and one small). For the connection method, please refer to the bicycle chain for two-person riding.

This is the simple principle of a wind turbine.

How to make a wind kinetic power generator

The difference between horizontal axis and vertical axis wind turbines lies in the following aspects:

1. Design method<. /p >

For the design of horizontal axis wind turbine blades, the theory of blade dynamics is commonly used. The main methods include Glauert method, Wilson method, etc. However, since the blade element theory ignores the flow interference between each blade element, and at the same time ignores the resistancestance of the airfoil when designing blades using blade element theory, this simplification inevitably leads to inaccuracy in the results. This simplification has little impact. on the design of the blade shape, but has a greater impact on the wind energy utilization rate of the wind wheel. At the same time, the interference between the blades of the wind wheel is also very strong, and the entire flow is very complex. It is impossible to obtain accurate results based on blade element theory alone.

The design of vertical-axis wind turbine blades was formerly based on the horizontal-axis design method and relied on blade element theory. Since the flow of vertical axis wind turbine is more complex than that of horizontal axis, it is a typical large separation unsteady flow and is not suitable for e-analysis.t to design using blade element theory. This is also an important reason for the vertical axis. The wind turbine has not been developed for a long time.

2. Wind power utilization rate

The wind power utilization rate of large horizontal axis wind turbines is mainly calculated by blade designers and is generally above 40%. As mentioned earlier, due to flaws in the design method itself, the accuracy of wind energy usage calculated in this way is highly questionable. Of course, wind turbines at wind power plants will plot wind power curves based on measured wind speed and power output. However, the wind speed at that time is the wind speed measured by the anemometer on the back of the wind wheel. as the speed and power of the incoming wind. The curve is too high and needs to be corrected. After application of thehe correction method, the wind energy utilization rate of the horizontal axis will be reduced by 30% to 50%. Regarding the wind energy utilization rate of small horizontal axis wind turbines, the China Aerodynamic Research and Development Center has conducted relevant wind tunnel experiments, and the measured utilization rate is between 23% and 29%. %.

3. Structural Characteristics

When the blades of the horizontal axis wind turbine rotate once, they are affected by the combined effects of the force of inertia and gravity. The direction of the inertial force changes at any time. , and the direction of the force of gravity changes at any time. The direction remains unchanged, the blade is therefore subjected to an alternating load, which is very detrimental to the fatigue resistance of the blade. In addition, horizontal axis generators are placed at an altitude of tens of meters, which brings a lot of inconvenience to the installation.lation, maintenance and inspection of generators.

The blades of the vertical axis wind turbine are much better stressed during rotation than those of the horizontal axis. Since the direction of the force of inertia and gravity always remains unchanged, the blades are subjected to a constant load. The fatigue life is longer than that of horizontal axis wind rotors. At the same time, the vertical axis generator can be placed under the wind wheel or on the ground for easy installation and maintenance.

4. Start-up wind speed

There is a consensus that the start-up performance of horizontal axis wind turbines is good. However, depending on the wind speed of small horizontal axis wind turbines driven. the China Aerodynamic Research and Development Center According to tunnel experiments, the starting wind speed is generally between 4-5m/s, and the maximum reached5.9 m/s. Such startup performance is obviously unsatisfactory. There is also an industry consensus that the starting performance of vertical axis wind turbines is poor, especially for Darrieus Ф-type wind turbines, which have no self-starting capability, which is also a reason which limits the application of the vertical wind turbine. axis wind turbines. However, for the Darrieus type H wind wheel, the conclusion is the opposite. According to the author's research, as long as the aerodynamic profile and installation angle are correctly selected, fairly good starting performance can be achieved. Judging from tunnel experiments, the starting wind speed of this Darrieus type H-shaped wind rotor only needs 2 m/s. , which is better than the horizontal axis wind turbine mentioned above.

Question 1: How to make a wind kinetic energy generator ins Minecraft Industry 2 Wind Kinetic Power Generator

Synthesis Method:

Iron Shaft* 2

Basic Mechanical Shell* 1

Wind kinetic energy generator* 1

NEI can see the summary table

Question 2: How to use wind power generators in Minecraft Industry 2 to generate electricity? There are two types in Industry 2.

One of them is kinetic wind power generation. Another option is wind power.

The methods of use are presented in turn.

Producing wind kinetic energy requires the following two types of machines.

A height of 150 is recommended. This can maximize the power generation capacity of the carbon rotor. As shown below, listed in order.

Log in.

Simply put the rotor on.

Wind energy. Just prepare this.

Set it up and connect it.

That's it.

Note: Wind power generation is not recommended. 1. Low energy production. 2. It breaks easily and needs to be replaced, especially in rainy and stormy weather.

Of course, wind power generation is just the opposite. In rainy and stormy weather, the rotor can produce maximum power output, and the power output capacity of the carbon rotor is about 125. The only drawback is that all the materials are iron, and most of the People can't afford carbon rotors. Sometimes Luck 3 is better. A carbon rotor requires approximately 4 groups of 20 carbons.

Question 3: How to create a wind kinetic energy generator in Minecraft Industry 2? Wind kinetic energy generator mainly converts wind energy into kinetic energy. Kinetic energy generators can convertkinetic energy into electrical energy. After docking both machines, turn on the rotor. The iron rotor has 6 grids. The steel rotor is made up of 8 grids. The carbon rotor is made up of 10 grids. Wind turbine: generates electricity throughout the day, production 0 ~ 4EU/s. How to get maximum power: Climb to the upper limit, which is the highest place, and place the generator one space below the upper limit. Keep the generator's 9X9X7 range away from other blocks. Note: It is recommended to use the first type, which has a large power generation capacity. The second type is very easy to break.

Question 4: How to use wind kinetic energy generator in Minecraft Industry 2. I remember there are two things, one is kinetic energy and the other is kinetic energy. wind turbine used together. Otherwise, try to see if awind turbine can produce electricity. There must be a rotor inside, like a fan page. Then place the wind turbine at a higher location and place the rotor. If the rotor moves, it means it is spinning.

The higher the place, the faster it spins and the more electricity it emits.

Question 5: How to generate and use kinetic energy from wind to generate electricity in Minecraft Industry 2. The official wiki states that the maximum wind power is 160 The new kinetic energy of the wind depends on the fan blades you use. But be careful in this place. When the carbon fan blades cannot blow, you can only use carbon fan blades.

You can make a wind detector and go up into the sky to measure it.

But even though it is 16x floor, I remember that the tallest is actually 165 floors, and the wind will increaseter.

Each fan blade has an operating range. If it exceeds the bearing capacity of the fan blade, it will not work if the wind force is lower than the corresponding wind force. corresponding wind force, it will cause a double loss. But also think about periods of rain and storms. Other fan blades often lose twice as much at this height (the wind is too strong)

Question 6: How to produce and use the kinetic energy of the wind to produce electricity in Minecraft Industry 2 ic2 Yes The one after the update and the one before the update

The previous one was placed directly in the sky and just connected to the wires

More Later, a rotor and a kinetic power generator were required. Please Baidu for details

p>

Question 7: My world.World 1.7.2 Industry 2 Experimental version How high is the kinetic power generator?What wind turbine is usually placed? 50 points New wind power depends on the fan blades you use.

The official wiki says the windiest level is on the 160th floor, but I remember the highest level is actually on the 165th floor. But pay attention to this place, basically only carbon fan blades can be used. Other fan blades often experience a loss twice this height (too much wind).

You can make a wind detector and go up into the sky to measure it.

Each fan blade has an operating range. If the wind force is less than the corresponding wind force, it will not work. If the wind force is greater than the corresponding wind force, it will cause double loss.

However, even with a 16x layer, the carbon fan blades cannot blow. However,You should also consider that when it rains or there are thunderstorms, the wind force will increase and exceed the bearing capacity of the fan blades.

Question 8: How to produce electricity from wind energy? Tap to turn the page and connect the power generation engine

Question 9: How to make a kinetic energy generator in Minecraft Industry 2. Energy engine synthesis method kinetic energy Iron casing*. 6 + heat generator + electric motor + iron handle = kinetic energy generator

As the picture shows

As the name suggests, the kinetic energy generator uses kinetic energy to produce electricity. The amount of electricity generated depends on the input kinetic energy. The kinetic energy input port of the kinetic energy generator

p>

The kinetic energy output port of the kinetic energy machine

Question 10: What metal and plastic wires are used for the wind kinetic energy generator in Minecraft?

  • Popular Focus
  • Where is the cheapest battery wholesale?

    Where is the cheapest battery wholesale in Tangxia, Sanyuanli, Baiyun District? There is an enterprise specializing in the independent production of electric vehicles in Tangxia, Sanyuanli, Baiyun District, Baiyun Sanyuanli Avenue, Baiyun Sanyuanli Street
    08-02
  • Four 3.7V lithium batteries in series and parallel produce 7.4V/4.4A. How to reduce it to 4.8V/4.4A?

    Four 3.7V lithium batteries in series and parallel produce 7.4V/4.4A. I personally think it is impossible to reduce it to 4.8V/4.4A. Because the discharge platform of lithium batteries is generally set
    08-10
  • What are the materials of the negative electrodes of lithium batteries?

    What are the materials of the negative electrodes of lithium batteries? The main commercial applications of lithium batteries include graphite, which is a sheet of copper used to guide current and which does not react. another safe
    08-02
  • The difference between 18500 and 26500 batteries

    What is the difference between 18500 and 26500 batteries? The answer above is 18650. The person asking the question should ask what is the difference between 18505 and 26500 batteries. In the case of Fuant ER1
    08-02
  • What does 3.7V 80mAh written on a lithium battery mean?

    What does 3.7V 80mAh written on a lithium battery mean? 3.7 V, 80 mA = 0.08 A, H means 1 hour, or 3600 seconds. Taken together, it is
    08-02
  • How long does a lithium battery (cell phone battery) last?

    How long does a lithium battery (cell phone battery) last? The lifespan of mobile phone batteries, under normal conditions of use and without serious impact, the lifespan set by the manufacturer must be 5 years.
    08-02
  • Will lithium batteries explode when charging?

    Will lithium batteries explode when charged? Will lithium batteries explode when charged? Lithium battery explosions usually occur during the charging process, because the negative electrode material of lithium batteries is graphite or other carbon materi
    08-02
  • Parameters of lgdas31865 lithium battery

    Parameters of lgdas31865 lithium battery The parameters of lgdas31865 lithium battery are as follows: LGDAS31865 is a model 18650 lithium battery with a capacity of
    08-02
  • What are the main components of lithium battery electrolyte?

    What are the main components of lithium battery electrolyte? The composition of lithium battery electrolyte is shown below. 1. Ethylene carbonate: molecular formula C3H4O3. Colorless transparent liquid (>35℃), room temperature
    08-02
  • Who are the lithium battery manufacturers in Shandong?

    What are the lithium battery manufacturers in Shandong? Shandong Shengyang Power Supply Co., Ltd. and Shandong Weineng Environmental Protection Power Technology Co., Ltd. 1. Shandong Shengyang Power Supply Co., Ltd. is located in Shengyang, Qufu City.
    08-02
  • Types of drone batteries available in 2024

    Part 1. Types of drone batteries available in 2024In 2024, drone batteries have advanced significantly, offering a range of options to cater to various needs in
    07-30
  • How long does it take to charge 26650 battery?

    How long does it take to charge a 26650 battery? The charging time for a 26650 battery is generally between 3 and 6 hours, but the precise time depends on the power of the charger and the capacity of the battery. in general
    08-02
  • For what?Sure, here's an article based on the phrase "For what?

    The simple yet profound question, "For what?" often serves as a gateway to deeper reflections on purpose and intention. It is a query that invites us to delve into the reasons behind actions, decisions, and circumstances that shape our lives and the wor
    08-02
  • Choosing the Right Cart Battery

    This comprehensive guide will walk you through everything you need about cart batteries, from understanding different types to making an informed purchase decision.
    08-02
  • 30mAh~500mAh 3.7 V Li-ion Battery

    Welcome to Ufine's collection of 3.7V lithium-ion batteries ranging from 30mAh to 500mAh. Explore a diverse range of compact and lightweight batteries suitable for various electronic devices,
    08-02
  • Here are 10 essential facts about drone batteries for 2024.

    10 Key Facts About Drone Battery for 2024 In 2024, drone batteries have advanced significantly, offering a range of options to cater to various needs in the consumer, commercial, and industrial sectors. Below are the primary types of drone batteries avai
    08-02
  • Could you please explain the difference among IMR, ICR, INR, and IFR 18650 batteries?

    What is the Difference Between IMR, ICR, INR, and IFR 18650 Battery?In 18650 batteries, discerning the differences among IMR, ICR, INR, and IFR types is fundamental for tailored and efficient battery usage. These distinct
    08-02
  • Safety considerations for cart batteries

    Selecting the ideal cart battery is crucial for ensuring optimal performance and longevity of your electric vehicle or vaping device. This comprehensive guide w
    08-01