ScooterDon't worry if the rear wheel nut cannot be removed with an electric air cannon, just use bolt loosening agent, you can also lubricate it with engine oil; and tap it with a hammer. Wait ten minutes, then lubricate and tap again. Some screws need to be lubricated and soaked in engine oil for a full day before they can be removed.
Whether or not there is a seal inside the rear axle bolt of a scooter depends on the specific situation. Some screws have their own pads, so there is no need to install a spacer, but some screws do not have a spacer, so there will be a spacer. You will know what type of screw the rear axle is.
When it is tight, it is straight thread, when it is loose, it is reverse thread, so the pulley screw is straight thread Herea simple and practical method for you. The nuts are straight threaded. If the nuts are screwed on, use a chopper to chop the nuts. Because this is real wire, use two new nuts when installing. It is better to use an air cannon to move them in the future, which saves time and If you buy it, don't buy a cheap one because it is not strong enough. It costs about 400-500 yuan, a magneto clip and an impact screwdriver. It's not very easy to use.
Use a 17# socket wrench to remove each screw counterclockwise. If it cannot be tightened, you can put a longer return rod on the sleeve. Do not tighten the socket in the opposite direction. It is better to use hexagons rather than plums.
What does it mean to step up and stand still. If it was too tight originally, the wrench you used is nots pretty good. Wheel bolts generally require a relatively large amount of torque and are best removed with a socket or eye wrench.
Scooter problems
The scooter's electronic shock absorber only works when the car starts from cold. It will automatically close shortly after starting, which is related to fuel consumption. It doesn't matter anymore. As long as the electronic damper is not broken it will not increase fuel consumption and if discarded it will cause difficulty starting or the inability to start when the car is cold. The high fuel consumption of scooters is mainly due to the transmission method and has almost nothing to do with the electronic shock absorber.
How to remove the windshield of Chuanling 150 scooter
Yours should be the most common phenomenon on Honda 125 Jiaying and Feimeng. In fact, some peoplehave already spoken to me about this issue, but have not been able to get confirmation. But there are a few things to note.
1: The carburetor of a scooter is usually connected to an electric shock absorber, which is the carburetor of a men's car. When the car is cold, the damper switch (pull wind) is used to allow operation. The car turns on easily. This electric fan does not turn off immediately after starting the car. Therefore, when the car is turned on but the electric fan has not reached the operating temperature and is turned off, and is still on, the basic phenomenon. will occur during startup or refueling. When the car is boring, it's like driving a man's car with the windshield open.
2: Nowadays, all motorcycles are equipped with a secondary circulation valve, which is the Euro III transmitter that we often callt. Because this gas recirculation combustion system also relies on the vacuum of the piston suction. , in other words, affects the most basic suction work of the engine.
3: BecauseWith the operation of the electric fan and the suction of the circulation valve, under the combined influence of the two systems, the cold start of this scooter will of course have a certain impact. As a result, the car that has not been warmed up will stall while driving.
As the weather in Guangdong has recently started to get a little cooler, this problem also occurred in my own car. There is a way to alleviate the situation without any modifications to the vehicle. Simply warm up the car 1-3 minutes earlier to give the electric fan enough time to heat up and return to its original position. Another method is to deactivate the European System III.
The steps arefollowing:
1. The panel with the Suzuki logo must first be removed. There are screws inside and remove them. the entire front.
2. Unscrew the screw on the black plastic under the faucet. This way you can remove the windshield.