What are the repair (maintenance) items of the 5T vehicle?

Vehicle maintenance is a top priority and repairs are only carried out if there are problems with the vehicle. How to reduce the vehicle maintenance rate depends on daily use and maintenance. Common knowledge of automobile repair and maintenance: The "three waters" testing of water tank, battery and wiper cannot be ignored. The "three waters" refers to water tank water, battery water and windshield wiper water. The liquid in the water tank is water and antifreeze. You should always check if the water level is sufficient. If the water level is relatively low, clean water or antifreeze should be added to the middle of the upper and lower limits when the car is cold. If you wish to perform a self-inspection, never open the water tank cap while the engine is running or within one hour after it has stopped. To avoid theburns due to splashing water from the hot water tank. Battery water also has upper and lower limits for water filling. When it is insufficient, add water from the battery. Do not add clean water to the battery every time, you need to check whether the power is enough or check the battery storage function. You can also find out if the generator and battery are normal. if there is any problem, please repair it in time to avoid your car breaking down halfway. When parking overnight, remember to turn off all switches in the car to avoid starting the engine the next day due to insufficient power. The water in the windshield wipers should also be checked frequently to see if the water level is sufficient. At the same time, check whether there is sediment in the water tank. It is best to remove the water tank and clean it, pI'll install it later. cleaning, then fill it with water. It's better to add a little detergent which can remove oil stains on the windshield. Plain water can be used instead, although a lack of wiper water will not cause the vehicle to break down, if dirt on the windshield is not present. cleaned in time, it may also affect driving safety. Then there are the wiper blades. Wiper blades are often overlooked. Temperature changes, sand, gravel, dust, etc. will shorten the life of the wiper blades. Once the wiper blades are damaged, you will not be able to see the road ahead clearly on rainy days. driving risks. This is why inspecting the wiper blades is also very important. It's also a good idea to clean the windows and wipers after it rains. How to perform inspection and maintenancebefore, during and after driving? 1. Before driving, the driver should insist on the following inspections of the vehicle: (1) Check whether the lights and turn signals work reliably; (2) Check whether the braking device is working properly, including the brakes and brake fluid level; and brake fluid level; (3) Check the fuel level; (4) Check whether the position of the rearview mirror is appropriate; to clean ; check whether the tire pressure and condition are normal; (7) Check whether the engine lubricating oil level meets the requirements; check whether windshield wiper and washer fluid levels and working conditions meet requirements; and the nuts of the exposed parts of the vehicle are secure; (10) Start the engine and check whether the engine runs normally, whether there is any abnormal noise, and whether all instruments and warning lights operate normally. 2. Inspection andnmaintenance while driving: When driving for a long distance, after driving a certain distance or for a certain period of time, you should choose a flat, wide, safe and reliable place to park your car for inspection and maintenance. interview. The following are usually carried out: check whether the engine and chassis are operating normally; whether various instruments operate effectively and reliably; check the steering gear and handbrake;and clutch operate normally and reliably; check tire pressure and remove inclusions in the tire tread; check for water, oil, and air leaks; inspect the entire exterior of the vehicle for any abnormalities; 3. Inspection and maintenance after car collection: Routine inspection and maintenance after car collection usually includes the following: check if the engine is runningoperates normally, listen for air leaks, check and refill fuel, oil and cooling water. ; follow regulations. Check lubrication points and add lubricating oil (grease); turn the oil filter handle 3 to 4 turns; touch the brake drum with your hands to see if it is hot or too hot; the temperature is below 0°C, there is no antifreeze. The cooling water must be drained; in very cold areas, the battery should be placed in a warm room and all switches and buttons should be turned off; checked and equipped; the exterior of the vehicle must be cleaned, and the cabin and compartment must be cleaned; and the master cylinder brake should be inspected whether the fluid level is within regulations, then press each button of the door switch, remove the ignition; Change the key and close the door. Once the car doorclosed, pull it again to see if it is locked. Regular maintenance of the automobile ignition system. In addition to daily maintenance, the automobile ignition system should also be subject to scheduled maintenance, if conditions permit, the quality, technical performance and operating conditions of the main parts should also be tested and adjustments need to be made. if necessary. During scheduled maintenance, two things must be done. 1. After the vehicle has traveled 1,000 kilometers, promptly remove the dust and oil from the outside of the distributor cover and body; check the primary circuit connection and wipe it of dirt on the outer surface of the spark plug. 2. What to do after the vehicle has traveled 5,000 miles: clean the dirt from the outside of the distributor, remove the distributor cover and clean the interior. Check the status ofcircuit breaker contacts and clean them. If the contact surface is uneven, it should be polished. Use a feeler gauge to check contact spacing. If it does not meet the requirements, an investigation must be carried out. condition of high voltage wires and terminals and is the distributor seat hole contact good? Clean the dirt on the outer surface of the ignition coil, and pay attention to the contact between the high voltage wire and the seat hole; check whether there is carbon deposits on the spark plug insulator skirt, whether the gap is appropriate, the general standard is 0.6-0.7mm, whether the gasket seal is in good condition, whether the spark plug is properly installed, etc. Only then can the ignition system be properly maintained. Inspection and maintenance of the handbrake after driving for a while. Like the foot brake pedal, the handbrake handle also has a traction strokenot. It is generally stipulated that when the handle is raised to 70% of the total travel, the handbrake system should be in the normal braking position, so check the handbrake