1. Add water to the water tank, first close the drain valve, add clean drinking water or purified water to the mouth of the water tank, then close the lid of the water tank.
2. Add engine oil There are two types of engine oil: summer and winter. Please do not mix them. When adding engine oil, pay attention to the oil dipstick until oil is added to the center mark of the oil dipstick, then close the oil cap. Excess oil will cause oil discharge and oil burning, which is the case. detrimental to the machine.
3. The diesel generator set uses independent external diesel barrels, which allows users to use oil barrels of different capacities according to their own operating conditions. use. The oil inlet and oil return of the machine must be distinguished. To ensure thatthe oil sucked into the machine is clean, the diesel is generally left to settle for 72 hours. The oil inlet position should not be inserted at the bottom of the machine. Oil cylinder to avoid sucking dirty oil and clogging the oil pipe. Use different diesel fuel depending on the season.
4. To pump diesel, first loosen the diesel pump nut, hold the oil pump handle with your hand, then pull and press evenly until oil enters the oil pump. Be careful not to use excessive force.
5. Bleed the air, loosen the high pressure oil pump bleed screw, then press the manual oil pump. You will see oil and bubbles overflowing from the screw. hole until you see Tighten the screw until all the oil comes out. At this time, the oil pump is filled with oil.
6. Connect the starter and distinguishz the positive and negative poles of the motor and the positive and negative poles of the battery. This is the positive pole, and the one on the side. the end is the negative pole. The two batteries need to be directly connected in series, can achieve the effect of 24 volts. First connect the positive pole of the motor. When connecting the positive pole, do not let the terminal touch other terminals. Then connect the negative pole of the motor. The terminal must be connected securely to avoid sparking and burning of the terminal.
7. Pneumatic switch, before starting the machine, or if the machine does not enter the power supply state, the switch must be in a state separated. The lower end of the switch. and the 4 terminals, these 3. These are three-phase live wires, namely V, U, W and N is the neutral wire. The neutral wire and any live wires are connected to a 220V lighting supply. Do not use a phase pto exceed 1/3 of the nominal power.
8. The instrument part, the ammeter, accurately reads the power consumption during use. Voltmeter, check the motor output voltage, frequency meter, frequency meter should reach 50Hz, which is the basis for detecting current and voltage conversion switch, conversion switching gear can not be zero, other gears are optional.
To detect the engine instrument data, the oil pressure gauge is used to detect the oil pressure of the diesel engine at full speed, it should not be less than 0.2Mp. The tachometer should be at 1500 rpm per minute, the water temperature meter indicates that the water temperature cannot exceed 100 degrees when in use (except in plateau areas, it is best water does not boil), and the oil temperature generally cannot exceed. 85degres.
9. Start, turn on the ignition switch, press the button for about 5 seconds and release it after starting the car. If the car does not start after the first ignition, pause for 15 seconds, start a second time and repeat the last action until the car starts. After starting the car, run it for 30 seconds, operate the high and low speed switch, and while the machine slowly shifts from idle to high speed, check the readings of all instruments. In the initial state, the HZ meter will increase to 55 Hz. At this time, the V voltmeter does not indicate any voltage.
Continue to increase the speed until the voltmeter rises between 400 V and 440 V. At this time the HZ meter will return to zero. Continue to increase the speed and the HZ meter will rise to between 50 and 52 HZ. When the voltage and speed are synchronized, it can beused normally.
10. Park the car. First turn off the air switch, turn off the power supply, adjust the diesel engine from high speed to low speed, let the machine idle for 3-5 minutes, then turn off the ignition switch. If it's winter, waterproof the tank to prevent freezing.