The overflow pipe is the first item on the right as shown: the overflow port
1 The overflow port of the solar water heater is usually located at a higher position on the side. the water storage barrel. When water is filled beyond this position, it will automatically flow out of the overflow port to prevent the water storage bucket from being full.
2. The position of the overflow pipe can be directly connected to a pipeline, and when the water exceeds this position, it will automatically overflow; it can also be equipped with a water level sensor and connected to an automatic water injection device, and when the water level reaches this position, the water injection will automatically stop.
3. Another function of the overflow hole on some solar water heater models is to vent air. When the water temperature in the water storage barrel is too high, the vapeur generated water can also be discharged from here. .
When the Sanle solar water heater is filled with water, what is the problem with the overflow pipe leaking?
There is one port too many -full at the high water level of the solar water heater. , and the overflow port is connected to the overflow pipe. The overflow pipe has two functions. One is to provide ventilation to ensure that the pressure in the solar water storage tank will not increase due to feed water pressure. The other is to ensure that the water level in the water storage tank reaches the overflow. Opening and excess water will drain from the overflow opening. When the overflow pipe overflows with water, it means the solar water heater is full of water. At this time, the water supply valve should be closed in time to avoid wasting water resources. . When filling with water, it is normal that a smallThe amount of water flows out of the overflow pipe because the very humid air inside the tank is continually exhausted from the overflow pipe.
What happens when the solar water heater is not full and water flows from the overflow pipe?Under normal circumstances, the overflow pipe will not overflow until the water is full if the water overflows before the water. is full, it may be due to the overflow pipe. This is caused by poor or damaged sealing of the port, or the water is really full and overflowing, but the instrument incorrectly detects and shows that it is not full. At that point you need to check. the water level probe and the instrument as well as the connection lines between them
I hope to adopt and thank you
Why is there no hot water in Sanle solar water heaterHow to use solar? water heater. When using the solar water heater, interested people will find thatIf the water supply time and water quantity are intelligently arranged, it will result in double the result with half the effort. Users who have just started using it may not be very clear about it. Over time, they will gradually develop experience and rules.
Tips for using solar water heaters:
A. When taking a bath, if the water in the solar water heater is used up and the person does not is not rinsed, you can run cold water for a few minutes, using the principle that cold water flows and hot water floats, you can take a bath by taking out the hot water from the vacuum tube .
B. Using the principle of A, if there is still some hot water left in the solar water heater after taking a bath and cold water is applied for a few minutes , hot water can be used to wash a pno one more. (Each vacuum tube produces 6.5 liters or 8 liters of hot water)
C. Determine the amount of water supplied based on the weather forecast to obtain a more satisfactory water temperature: if the weather is good, the water can be filled to the top, if it is cloudy or cloudy. If it rains, the water in the tank will be filled with half a tank of water; if it rains, the original water will be retained and no cold water will be poured.
D. After taking a shower at night, if there is still half of the hot water near 70℃ in the water heater tank, in order to avoid heat loss excessive (the less water, the faster the heat dissipation), the amount of water should also be determined based on the weather forecast. On sunny days, fill the water with 2/3 of the water, and on cloudy and rainy days, fill with 2/3 of the water. the water.
E. The role of the auxiliary water tank: theAuxiliary water tank mainly serves areas with regular water supply and unstable water pressure. The water storage capacity is between 1/2 and 3 times that of solar water. water heater. It is installed on the roof of the building. The main function is to mix cold water with water to adjust the water temperature when bathing. In addition, it can be used as a water storage tank when the water is turned off and can also precipitate impurities in the water in areas without tap water. .
F. Hot and cold water adjustment: The steps for adjusting the water temperature of the solar water heater are as follows: first open the cold water valve, adjust the cold water flow appropriately, then open the hot water valve. adjust until the desired bath temperature is obtained. Additionally, the amount of cold water can be determined empirically based on weather conditions.eorological. Be careful not to point the nozzle towards the human body to avoid burns.
G. Wind resistance measurements: Since the components of the solar water heater are reliably connected, the wind resistance performance mainly depends on its installation and fixing method. Currently, Huangming uses 8# and galvanized iron wire. Extended expansion bolts for mounting, front and rear. It forms an eight shape and has good wind resistance. In addition, in areas with strong winds such as coastal areas, the effect will be better if the support structure is changed. the back plate is removed and secured with steel strands used to secure telephone poles.
H. How to extend the service life: In order to extend the service life of the solar water heater, users should pay attention to the following points during use:
1 . After the water heateris installed and fixed, non-professional personnel should not move or disassemble easily to avoid damage to key components.
2. There should be no debris around the water heater to eliminate the hidden danger of hitting the vacuum tube.
3. Check the exhaust hole regularly to ensure that it is smooth to avoid inflation or deflation of the water tank.
4. When cleaning the vacuum tube regularly, be careful not to damage the tip of the vacuum tube.
5. In winter, the pipes should be prevented from freezing and cracking, and the exhaust pipe should be kept clear.
6. Solar water heaters equipped with auxiliary electric heating devices should pay special attention to water supply to avoid dry burning without water.
Sanle solar water heater