Turn off the solar water heater, turn off the water source to the solar water heater and remove the water inlet.
1. Turn off the solar water heater: Before disassembling the water inlet of the solar water heater, turn off the solar water heater and wait for the temperature of the solar water heater to drop to avoid burning during disassembly.
2. Turn off the water source of the solar water heater: Before dismantling the water inlet of the solar water heater, turn off the water source of the solar water heater and wait for the water pressure to drop before operation to avoid accidental injury caused by excessive water pressure.
3. Disassemble the water inlet: Find the water inlet of the solar water heater at the bottom of the water tank, loosen the screws underneath, and then remove the water inlet pipe. Before disassembly, confirm the connection method between the water inlet and the water pipe to avoid incorrect disassembly. Be careful whendisassembly to avoid damage to the connection threads between the water inlet and the water heater, so as not to affect the sealing effect.
How to dismantle a solar water heater
If you want to dismantle a solar water heater, it is best to choose a cloudy day. First, drain all the water in the solar water. Start with the first pipe on the solar side. Disassemble it, attach the rubber ring at the connection between the vacuum tube and the water tank, hold both ends of the vacuum tube with both hands, turn it left and right to withdraw. the vacuum tube from the base, then remove it while rotating it.
From a safety point of view, it is better to hire professionals to disassemble solar tubes, because some solar tubes that have been used for a long time are difficult to disassemble safely. When disassembling solar tubes, you cannot choosea time with strong sunshine, because when dismantling the solar tubes you have to drain all the water from the solar panels. If the sun is too strong and there is no water in the tubes, the strong sunlight will do it. shorten the life of vacuum tubes, or even damage the vacuum tube.
When disassembling the solar tube, it is best to use water soaked in detergent or lye to lubricate the vacuum tube. Remove the rubber ring between the vacuum tube and the water tank, then hold the vacuum tube with it. with both hands and use a little force to remove the other end of the vacuum tube. Remove one end of the circlip, then gently remove the vacuum tube from the water tank. During the disassembly process, you should not use too much force, otherwise the solar tube may burst and cause injury to people. Therefore, non-professionals should pay attention to safety when disassembling the tube solaire.
During the process of disassembling the solar tube, if the rubber ring cannot rotate for a long time, you can use dishwashing liquid to apply to the contact area between the tube and the silicone ring to increase lubrication, then apply it to the rubber ring. When disassembling the solar tube, it is best to disassemble it from the first tube on the solar side, which will make the operation easier.
Solar tube installation and disassembly methods
Not only does the installation of a solar water heater require professional techniques, but the removal also requires attention . If the steps are wrong, it will be. easily affect its lifespan. 1. First of all, it is better to choose a cloudy day, morning or evening for disassembly, because all the hot water from the solar water heater should be discharged before disassembly (to avoid being burned by the infiltrationss). hot water when removing the pipe). 2. It is best to disassemble the pipe with dish soap or laundry detergent. Dip the vacuum tube into water to lubricate the vacuum tube. At the same time, pay attention to the angle of the vacuum tube and pull it gently. Avoid pulling the angle to prevent the vacuum tube from bursting and causing injury to people.
Installation of solar tube and disassembly method is as follows:
Tools/Materials: SANGGAOXSY-24 solar water heater, gloves, dish soap.
1. First, drain the water from the solar water heater pipe.
2. Then wear gloves and buckle the rubber ring at the connection between the vacuum tube and the water tank.
3. Buckle the rubber ring and the tube can be removed.
4. When installing, you should first apply a little dishwashing liquid to the installation part of the pipe to lubricate the installation.
5.Then aim for the hole at the top of the water, gently rotate and push up.
6. Push it forward about 15 centimeters, aim at the bottom, rotate it slightly and remove it.
7. Slowly put it into the bottom, as shown in the picture below, the installation is successful.