It is better to choose a cloudy day when you want to disassemble the solar tube. First, drain all the water from the solar panel. Start by removing the first tube from the solar side and attach the rubber ring at the connection. between the vacuum tube and the water tank. Hold both ends of the vacuum tube with both hands, twist it left and right to remove the vacuum tube from the base, and then remove it while rotating it.
From a safety point of view, it is better to hire professionals to disassemble solar tubes, because some solar tubes that have been used for a long time are difficult to disassemble safely. When dismantling the solar tubes, you cannot choose a weather with strong sunshine, because when dismantling the solar tubes, you need to drain all the water from the solar panels. If the sun is too strong and there is no water in the tubes, the strong light from the ssun will do it. shorten the life of vacuum tubes, or even damage the vacuum tube.
When disassembling the solar tube, it is best to use water soaked in detergent or lye to lubricate the vacuum tube. Remove the rubber ring between the vacuum tube and the water tank, then hold the vacuum tube with it. with both hands and use a little force to remove the other end of the vacuum tube. Remove one end of the circlip, then gently remove the vacuum tube from the water tank. During the disassembly process, you should not use too much force, otherwise the solar tube may burst and cause injury to people. Therefore, non-professionals should pay attention to safety when disassembling the solar tube.
During the process of disassembling the solar tube, if the rubber ring cannot rotate for a long time, you can use dishwashing liquid to apply to the contact area betweenthe tube and the silicone ring to increase lubrication, then apply it to the rubber ring. When disassembling the solar tube, it is best to disassemble it from the first tube on the solar side, which will make the operation easier.
How to remove the vacuum tube of the solar water heater
The installation and removal methods of the solar water heater are as follows:
Tools/Materials: SANGGAOXSY -24 solar water heaters, gloves, dish soap.
1. First, drain the water from the solar water heater pipe.
2. Then wear gloves and buckle the rubber ring at the connection between the vacuum tube and the water tank.
3. Buckle the rubber ring and the tube can be removed.
4. When installing, you should first apply a little dishwashing liquid to the installation part of the pipe to lubricate the installation.
5. Then aim for the hole at the top of the water, fGently rotate and push upwards.
6. Push it forward about 15 centimeters, aim at the bottom, rotate it slightly and remove it.
7. Slowly put it into the bottom, as shown in the picture below, the installation is successful.
How to remove the solar vacuum tube?
When disassembling, it is best to use water soaked in detergent or washing powder to lubricate the vacuum tube. At the same time, pay attention to the angle of the vacuum tube and avoid pulling it gently. the angle to prevent the vacuum tube from bursting and injuring people. Additional Information When disassembling solar vacuum tubes, you should pay attention: First of all, it is better to choose a cloudy day, morning or evening for disassembly, because you need to drain all the hot water. water in the solar water heater before disassembly (to avoid heat leakage when disassembling the tube) water burns) OnceWith the vacuum tube turned, gently push it upwards and enter about 20 centimeters into the insulated bucket of water. Gently lift the bottom of the vacuum tube and slowly remove it. Disassembly is complete.
How to do it. remove the solar vacuum tube
Remove the first tube from the solar side first, as it has a larger contact area and is less likely to damage the vacuum tube.
The specific steps are as follows:
1. Hold the upper and middle parts of the vacuum tube with both hands and twist it left and right. Note that older solar panels work harder.
2. While rotating, push up to remove the vacuum tube from the base.
3. Lift the lower end of the vacuum tube, twist it and remove it. That's all. If it is difficult to turn, use a syringe to draw up the dishwashing liquid and inject it into the rubber fitting between the vacuum tube and thehe was.
Detailed information
The points to note when disassembling solar vacuum tubes are:
1. First of all, it is recommended to do the following: you choose to dismantle in the dark during the day, morning or evening, because you need to drain all the hot water from the solar water heater before dismantling (to avoid getting burned by the hot water that seeps in when removing the pipe).
2. When disassembling, it is recommended to use water soaked in detergent or washing powder to lubricate the vacuum tube. At the same time, pay attention to the angle of the vacuum tube and avoid it. pull the angle to prevent the vacuum tube from breaking.
3. After the vacuum tube is disassembled, it must be packed in special polyester foam compartments and placed in special cartons to avoid shock during transportation.
The solar vacuum tube is the heart of the solar water heater. Its structure is like aelongated thermos bottle. There is a void between the inner and outer layers. The surface of the inner glass tube is covered. a spectrum-selective absorption coating using a special layer to further absorb energy from solar radiation.
Baidu Encyclopedia - Solar Vacuum Tube
The specific method of removing the solar vacuum tube solar vacuum is as follows:
1. First of all, we must wear plastic gloves to avoid burning our hands when disassembling the solar vacuum tube
2. collecting tube in contact with the bucket of water, we can apply a little dish soap, which will be more convenient for us to disassemble.
3. Hold the vacuum tube with both hands, use force and twist it left and right, once to the left, then to the right. Try several times. Some of the rusty tubes require several turns. turn. Once the vi tubecan turn, we slowly push it up and push it out.
Detailed information
When disassembling solar vacuum tubes, you should pay attention to:
1. The best time for disassembly is as follows. cloudy or cloudy in the morning or evening, because you have to drain all the hot water from the solar water heater before dismantling it (to avoid being burned by the hot water seeping in when dismantling the pipe
2); . It is best to use a cleaner when disassembling. Use alcohol or lye water to lubricate the vacuum tube, and at the same time, note that the angle of the vacuum tube should be pulled gently, and avoid pulling the angle to avoid the tube when empty does not burst and injure people;
3. Once the vacuum tube is dismantled, it must be installed; in special polyester foam compartments and placed in special boxes to avoid shocks during transport.
Reference materials:
Solar vacuum tube-Baidu Encyclopedia