The disassembly and assembly of solar water heaters requires certain skills and precautions. Here are the general steps for disassembly and assembly of solar water heaters:
Disassembly of solar water heaters:
Turn off the water heater: First of all, make sure that the hot water supply to the solar water heater is turned off. You can close the valve connected to the water heater or turn off the power to the water heater.
Drain the water heater: Open the water heater drain valve and completely drain the water from the water heater. This step aims to reduce weight during disassembly and prevent water leaks.
Disconnect the water pipe: Use a wrench or other suitable tool to gently loosen the connection between the solar water heater and the water pipe. This usually includes the inlet and outlet pipes.
Disconnect the power source (if applicable): If the solar water heater is operating on a power sourceelectrical connection, make sure the power is turned off and the electrical connection is disconnected.
Remove the mounting bolts: Check the mounting bolts or brackets of the solar water heater, use suitable tools to loosen and remove them.
Lift the water heater carefully: Lift the solar water heater carefully to ensure that it is not damaged or bumped during transportation.
Installing a solar water heater:
Prepare the installation location: Choose a suitable location to install the solar water heater and ensure that the support or the fixture is firm and reliable.
Install the fixing bolts: According to the design and requirements of the solar water heater, install the fixing bolts or brackets in the predetermined position.
Connect the water pipes: Connect the water inlet pipe and the water outlet pipe, making sure that theThe connection is watertight and well sealed. Use appropriate sealing materials, such as pipe sealing tape or pipe putty, if necessary.
Connect to a power source (if applicable): If your solar water heater requires a power source, make sure it is properly connected and perform all safety checks. necessary security.
Water Filling: Open the water inlet valve and inject water into the solar water heater system. Make sure the water is circulating properly and check for leaks.
Disassembly method of Xinxiang solar water heater
The steps to disassemble the indoor solar water heater are as follows:
1. Turn off the power supply or close the natural gas valve.
2. Empty the water from the water tank. Attach a hose to the drain valve at the bottom of the water tank, then insert the other end of the hose into the sink orbucket, open the drain valve and drain the water from the tank.
3. Remove the hoses from the water tank. Remove the straight and corrugated pipes from the tank.
4. Remove the transition hose on the water tank. Unlock the adapter tube and bend the transition tube, then remove the protruding clamp nut.
5. Remove the bracket and flange. Loosen the bracket and flange nuts and remove them.
6. Remove the protective cover on top of the water heater. Use a wrench to loosen the screws of the protective cover, then remove the protective cover.
7. Remove the pipes from the water heater. Remove the nuts from the water heater connections and other connected pipes.
8.Remove the protective cover at the bottom of the water heater. Loosen the screws of the protective cover and remove the protective cover.
9. Remove the water heater. Loosen the water heater nuts and remove the water heater.
Voici the steps for dismantling an indoor solar water heater. It should be noted that during the disassembly process, you must handle it carefully to avoid damage to the water heater. If you are unsure of your disassembly abilities, it is best to ask a professional to carry out the disassembly operation.
How to disassemble a solar water heater
The disassembly process of Xinxiang solar water heater should be carried out carefully. Here are the specific steps.
Step 1: First remove all water lines and power cords from the water heater. Be sure to turn off the power supply to avoid any risk of electric shock.
Step 2: Remove the solar collector bracket. The support is very important because it supports the entire solar collector system. The bracket and solar collector are usually attached with screws, so you need to use a wrench or electric wrench to remove it.
Step 3: Disassemble the solar collector. Solar collectors are usually mounted on brackets, so before disassembly, you need to use an electric wrench or wrench to remove the screws and remove the solar collector one by one.
Step 4: Remove the water tank. The water tank of the solar water heater is usually installed on the roof and should be removed using an electric wrench or wrench and placed in a suitable place.
Step 5: Disassemble the pipeline. Carefully remove the connections between the pipes and the solar water heater. If necessary, use a wrench or pliers to facilitate removal.
Step 6: Arrange the disassembled parts. The disassembled parts of the solar water heater should be sorted and sorted into categories.
In short, disassembly of the Xinxiang solar water heater requires patience and caution, so as not to damage the parts for further use or recycling. The heatDisassembled ffe-eau solar can be sent to the relevant recycling sites or recycled by other channels.
Drain the water first, then remove the connecting water lines to see if you want to move the solar or pack it. If you want to move it, you can move it by dismantling the water pipes. If there is a big movement, you need to dismantle the suction pipes slowly one by one, take them out, pour water, wipe them clean. and keep them. After dismantling them, start dismantling the insulating bucket. Remove the clips on the top bucket and slowly pull it out to drain the water inside. Pack it in a box and store it.
Solar water heater installation method ()
1. We first go to the mall to buy a solar water heater, then check whether the accessories inside are complete, and check whether the tools we have for installation are complets.
2. Then calculate the direction of the sun, otherwise our solar water heater will have no effect.
3. The next step is formal installation. We build a cement pier on the roof, then install the expansion screws, then install some items to secure the water heater.
4, then connect the water heater circuit. The red wire is the live wire and the white wire is the neutral wire.
5. Install the water heater motherboard. Although the motherboard is made of iron, we must pay attention to handle it carefully and avoid damage, otherwise it will be useless.
6. Finally, install some electronic components, such as the thermometer, install them and then test them.