How to use Sangle Solar:
1. Scientifically choose the water filling time: It is strictly prohibited to fill the water when the weather is particularly hot and the water temperature is particularly high, and it is strictly prohibited to add water immediately after the water runs out. Due to the strong sunlight in summer, the temperature of solar vacuum tubes in the air reaches 270°C to 400°C under the irradiation of the sun. Supplying water at this time can easily cause the vacuum tube to burst. Water supply should be carried out two hours before sunrise in the morning or after sunset in the evening. This can guarantee the service life of the solar vacuum tube.
2. Reasonably adjust the hot and cold water valves: The steps of adjusting the water temperature of the solar water heater: first open the cold water valve, adjust the cold water flow of mappropriate temperature, then open the hot water valve and adjust until the required bath temperature is obtained. In summer, due to prolonged sunshine, the temperature is higher and domestic hot water consumption is lower. As a result, hot water from solar water heaters often has a higher temperature, usually reaching over 60°C.
For ordinary households, the distance between the water storage point and the solar water heater water point is often long. At this time, the water temperature in the water pipes can reach around 35°C due to the water temperature. high temperature in summer. Therefore, when we turn on the water heater, the normal temperature hot water in the water pipe will be discharged first, and after a minute or two, the high temperature hot water will be discharged. If you are not careful, you may burn yourself. your skin.
3. Use judiciously hot water from the tail: When you take a bath, if the water in the solar water heater is used up and the person has not rinsed, you can run cold water for a few minutes and use cold water to pour and hot water to pour. The principle of floating is to make the hot water flow out into the tube, then you can continue to take a bath. If after taking a shower there is still some hot water left in the solar water heater, and you add cold water for a few minutes, the resulting hot water will be able to wash an additional person.
In addition, please note that when adjusting the water temperature in the shower, the nozzle should not face the human body to avoid burns.
4. Determine the amount of water to fill according to the weather conditions: you can get a more satisfactory water temperature if the weather is good the next day, you can refill itof water if the weather is nice. cloudy or cloudy, fill it with half a tank of water.
It rained all day, so the original water was retained and no cold water was provided. After taking a shower at night, if there is still half of the hot water near 70 degrees in the water heater tank, in order to avoid excessive heat loss (the less there is water, the faster the heat loss), the amount of water should also be determined based on the water temperature and weather forecast. If the weather is good tomorrow, the water will be full; if it rains tomorrow, the water will be 2/3 full.
5. Check the exhaust hole regularly: Check the exhaust hole regularly to ensure that it is smooth to avoid inflation or deflation of the water tank; For solar water heaters equipped with auxiliary electric heating devices, pay special attention to the water supply foravoid dry burning without water.
At the same time, check whether the insulation layer of the solar water pipe and the anti-UV tape are aging and cracking. If the water supply pipe is exposed, it will easily become hard and brittle, crack. and flees under exposure to the sun. Users install layers of insulation and UV tape in advance to fully protect water pipes.
6. Pay attention to lightning protection: Due to the need for heating, solar water heaters are usually installed high on the roof. They are prone to lightning attacks during thunderstorms, which will not only cause damage to the roof. solar collector panels, but also cause direct lightning along power lines, water pipes, etc. When it enters the room, people inside or household appliances may be struck by lightning.
By conséHowever, it is strictly prohibited to use solar water heaters during thunder and lightning. At the same time, the entire metal circuit of the solar water heater must be protected accordingly and a lightning protection device must be installed. Since entering the heatwave of summer, with the increase in summer thunderstorms, some solar water heaters that have not taken lightning protection measures have hidden safety risks.
Detailed information:
1. First of all, remember not to touch electrical appliances with wet hands. You should not use the leak protection cap as a switch and you cannot start the machine frequently. .
2. If you notice that there is hot water in the cold water pipe during useation, you should turn off the hot water in time and find competent personnel for diagnosis and repair. This will prevent hot water from flowing. flowing back and burning the cold water line.
3. Do not use the solar water heater if you encounter thunderstorms, etc. What you need to do at this time is to fill the water in the water tank so that it can maintain its weight, and then turn off the power.
Should the water tank of the Sanle balcony wall-mounted solar water heater be placed horizontally or vertically?
The Sanle solar water heater is a water heater that uses solar energy for heating. It uses high-efficiency solar collectors to convert solar energy into thermal energy and transfers the thermal energy to the water via the heat exchanger inside the water heater, thereby heating the hot water. Sanle solar water heater has the advantages of energy saving, water protectione environment, safety, reliability and long life. It is suitable for hot water supply in homes, hotels, schools and other places.
Must be placed vertically. The design is to place it vertically so that all aspects can be used normally, it can be used for a long time, it is safe, and the quality can be guaranteed. If it is placed horizontally or diagonally and the normal design is changed, it can be used, but safety cannot be guaranteed.
There are three ways to drain the electric water heater:
1. Close the water inlet faucet, open the water outlet faucet and install the safety valve (installed on the cold water pipe). inlet with one-way direction indicator) Valve) the handle is raised, this method drains the water slowly.
2. Close the water inlet valve, remove the mixing valveuse and the safety valve and drain the water quickly.
3. Close the water inlet valve, open the water outlet valve and unscrew the waste water outlet nut to release the water most quickly.
It is recommended to use the second method, as it is easy to use and the layout is cleaner.
To drain the gas water heater, there is a small long handled screw at the bottom, simply unscrew it and drain it.