I like. Solar water heaters are divided into vacuum tube solar water heaters and flat panel solar water heaters based on their structural shapes. The water pressure of this item installed on the roof can go down smoothly and reach a distance of two meters, so the water from the shower head installed by this item is normal. Solar energy mainly relies on evacuated tube solar water heaters, which account for 95% of the domestic market share.
How to install a shower head with solar water heater
The thermostatic faucet can automatically balance cold and hot water in a very short time. time thanks to the thermostatic adjustment valve. core supplied with the faucet. The water pressure is adjusted to maintain the stability of the outlet water temperature, without any manual adjustment.
The mixed hot water used for showering is sprayed directly onto the chuman body through the shower head. Maintaining a consistent temperature can greatly improve the safety and comfort of showering. A thermostatic mixer can achieve this goal.
Care tips
1. Please ask experienced professionals for construction and installation. When installing, the shower head should try not to collide with hard objects and not leave cement, glue, etc. on the surface to avoid damaging the gloss of the surface coating. Pay special attention to cleaning the debris in the pipes before installation, otherwise the shower head will be blocked by the debris in the pipes, thereby affecting its use.
2. When the water pressure is not less than 0.02 mPa (i.e. 0.2 kgf/cubic centimeter), after using it for a while, if you find that the flow water decreases or even the water heater stalls, youWe can gently unscrew the screen cover at the water outlet of the shower head to remove impurities, and it will generally be restored to its original state. But remember not to disassemble the shower head by force. Due to the complex internal structure of the shower head, non-professionals are not allowed to disassemble it without authorization.
3. Do not use too much force when opening and closing the shower faucet and adjusting the shower water outlet mode. Just turn it gently. Even a traditional faucet doesn't require much effort. Be especially careful not to support or use faucet handles and shower brackets as handrails.
4. The metal hose of the bathtub shower head should be kept in a naturally stretched state and should not be wrapped around the faucet when not in use. At the same time, be sure toDo not form a dead angle at the joint between the pipe and the faucet to avoid breaking or damaging the pipe.
Step 1:
1) As shown in Figure 1, wrap the two elbow joints (1) with raw material tape and use an adjustable wrench to tighten them. Tighten it to the water outlet joints in the two installation holes on the wall. After tightening, make sure that the center distance of the two elbow joints is 150 mm.
2) Put the two decorative covers (2) on the elbow joints;
3) Insert the installation washer (3) into the elbow joint [1] and use a wrench to tighten the installation nut (4) on the two elbow joints to secure the faucet on the upper wall.
Note:
1. After installation, the faucet should be level and not tilted, approximately 900-1100mm from the floor.
2. key to install the faucet 』Be careful not to damage the plating surface.
Step 2:
1) As shown in Figure 2, drill three holes with a diameter of 6mm and a depth of 35mm at a position approximately "H" from the faucet outlet joint. . ;
2) Push the expansion tubes into the installation holes and secure the wall-mounted base to the wall with self-tapping screws. Note: The wall base should be on the same center line as the faucet outlet joint.
3) Before drilling, wrap the faucet with a cloth 9 to prevent the faucet from being stained or bruised .
4). The height “H” should be determined according to the actual product during actual installation.
Step 3:
1) As shown in Figure 3, insert the sealing ring C into the lower end A of the switching valve.
2) Tighten the lower end A of the switching valve and the upper end B of the faucet through the threads.
3) Before drilling, wrap the faucet with a cloth 9 to prevent robinet is stained and bruised. Note: Be careful not to damage the veneer surface when tightening with a wrench.
Step 4:
1) As shown in Figure 4, tighten end B of shower rod 3 and end C of shower valve switching through the threads (shower column End B of the rod 3 must have a sealing ring 5).
2) Place the decorative cover 2 into the end A of the shower rod 3, then insert the end A into the wall base 1, tighten it with three set screws 4 on the end A, and finally put the decorative cover Push the cover 2 against the wall;
3) After installation, turn on the water inlet switch J to rinse the pipe thoroughly.
Step 5:
1) As shown in Figure 5, connect the end of nut A of the shower hose to joint B behind the body of the switching valve. C to the end D of the spray and insert J into the seat ofshower 2 (attention: both ends of the shower hose must have washers 1)
2) Tighten the upper jet 3 on the shower rod.