With continued advancements in technology, many homes are installing electronic water meters. This not only saves a lot of work, but also allows more accurate values to be read. However, if the electronic water meter runs out of power, the electronic water meter runs out of power. the battery should be replaced in time. So, do you know how to replace the battery of an electronic water meter and what problems should be paid attention to when using an electronic water meter?
1. How to change the battery of an electronic water meter
Find the battery compartment behind the electronic water meter, use a small Phillips screwdriver to unscrew it, remove the old battery. inside, then replace it with a new battery. It should be noted here that water meters generally use 3.6 volt lithium batteries and there are many typesof battery plugs, so be sure to confirm them in advance.
2. What problems should be paid attention to when using electronic water meters
1. If there is a significant error in the value read by the electronic water meter used at home, it is probably caused by the electronic water meter. The internal chip is damaged, and you should contact after-sales personnel for repair in time so that it can be used normally.
2. If there is an error in the data displayed by the water meter, the water flowing into your home may have water quality problems. For example, water contains too many impurities, which affects. normal operation of the electronic water meter during operation, special attention should be paid to this situation.
3. There are many types of electronic water meters. Consumers can choose the e meterto the appropriate one based on their real needs. In addition, if the water meter is installed unreasonably, it may cause data errors, so it should be installed by professionals.
4. When installing a water meter, the chosen location is also particularly important. It should not be installed in an area where the sun can shine. If a plug-in card water meter is used, it should be installed in a location where the card can be easily removed.
As for how to replace the battery of an electronic water meter and what problems should be paid attention to when using an electronic water meter, I will first present it here. Do you understand it? An electronic water meter should be replaced after prolonged use. So you can continue to use it.
My water meter is not producing water. Is the battery dead? How many youmps usually lasts the battery?
We will install water meters in our houses. They can be used. To record water consumption at home, the water meter must also be installed with a battery. Is there a way to determine if the water meter battery needs replacing?
1. How to determine if a water meter battery needs to be replaced
1. Today's water meters are very smart. One type of smart water meter is an inserted IC card. in it. If the battery needs to be replaced, it will be clearly displayed on the electronic screen of the water meter. The most direct manifestation is that the water meter numbers above have disappeared. At present, it is not because the water meter is defective, but because the water meter does not have a battery, reminding you that it needs to be replaced.
2. Some water meters are smarter and decsound alarms in advance.
3. If you find that the water meter reading at home is not particularly accurate, it could be that the battery is discharged, or the smart water meter is malfunctioning.
4. Some people have also reported that if the pre-stored water in their home has run out, but the water meter valve is not closed and there is still water flowing out of the water meter. 'water. meter, in this case it also means that the water meter battery is dead. The electricity is cut off.
5. In addition, low voltage detection method can be used. When the battery power is low, we can close the motor valve, and it will display that the voltage is too low or the valve needs. must be closed and a new battery replaced.
2. How to replace the water meter battery
1. First you need to remove the top screws and remover the old battery, and the battery compartment is directly at the bottom. of the water meter.
2. Disconnect the battery pressure connection. Typically, two-cell lithium batteries are used. Install the new battery, paying attention to the positive and negative poles.
3. At the same time, check whether it is firmly connected to the sheet metal, then fix the cover with screws. Check if the numbers on the surface display normally, which means the installation is in place. .
3. How long do smart water meter batteries last?
Generally, manufacturers can promise that smart water meter batteries can be used for more than three years, even 5 years . years. As long as you pay attention to maintenance and care, the battery can be used for so long under normal circumstances, 3-6 years is relatively common.
The content cThe above explains how to determine if the water meter battery needs to be replaced. You can watch its LCD screen. If there is no digital display, it means a new battery needs to be replaced. Is handed over, replaced.
If the water meter is not producing water, the water meter battery may be dead. If there is a display, but there is no response when inserting the card, it means that the lithium battery of the water meter is broken and the solenoid valve cannot be open, or the water meter card reading circuit is broken, or the card holder is broken.
1. The battery of a smart water meter can be used for 3 to 6 years.
At present, the average quiescent current of the water meter module is less than 3ua, and the total power consumption of the power supply is about 970mA in 6 years. However, as the water meteris used, the internal resistance increases and the power consumption also increases. Generally speaking, the actual available power is 1200 to 1300 mah.
2. The average battery life of plug-in water meters is more than 2 years.
Detailed information:
If you want to replace the battery before unlocking, the battery Should be replaced before the power goes too low or the water is turned off. When the power cannot be turned off, the battery needs to be replaced online, which is more difficult.
The water meter battery is connected by a 2-pin plug and socket cable. The wires are thin and short, the solder joints are stuck together, and the operating space is small. It is easy to cut off the power supply and cause a blockage.