|
SIST EN 4499:2009
01-maj-2009
Aeronavtika - Vijaki, 100° ugrezna glava, križna zareza, polno steblo, ozka
toleranca, kratek navoj, iz titanove zlitine, anodizirani, z aluminijem pigmentiranim
premazom - Klasifikacija: 1100 MPa (pri temperaturi okolice)/315 °C
Aerospace series - Screws, 100° countersunk reduced head, offset cruciform recess,
close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium
pigmented coating - Classification: 1 100 MPa (at ambient temperature) / 315 °C
Luft- und Raumfahrt - 100° Senk-Paßschrauben, mit kleinem Kopf, mit
Flügelkreuzschlitz, kurzes Gewinde, aus Titanlegierung, anodisiert, mit
aluminiumpigmentierter Beschichtung - Klasse: 1 100 MPa (bei Raumtemperatur)/315 °C
Série aérospatiale - Vis à tête fraisée 100° réduite, à empreinte cruciforme déportée, fût
normal à tolérance serrée, filetage court, en alliage de titane, anodisées, avec
revêtement alumino-organique - Classification: 1 100 MPa (à température ambiante) /
315 °C
Ta slovenski standard je istoveten z: EN 4499:2009
ICS:
49.025.20 Aluminij Aluminium
49.025.30 Titan Titanium
49.030.20 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN 4499:2009 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 4499:2009
---------------------- Page: 2 ----------------------
SIST EN 4499:2009
EUROPEAN STANDARD
EN 4499
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2009
ICS 49.030.20
English Version
Aerospace series - Screws, 100° countersunk reduced head,
offset cruciform recess, close tolerance normal shank, short
thread, in titanium alloy, anodized, with aluminium pigmented
coating - Classification: 1 100 MPa (at ambient temperature) /
315° C
Série aérospatiale - Vis à tête fraisée 100° réduite, à Luft- und Raumfahrt – 100° Senk-Paßschrauben, mit
empreinte cruciforme déportée, fût normal à tolérance kleinem Kopf, mit Flügelkreuzschlitz, kurzes Gewinde, aus
serrée, filetage court, en alliage de titane, anodisées, avec Titanlegierung, anodisiert,mit Aluminium pigmenttete
revêtement alumino-organique - Classification: 1 100 MPa Beschichtung - Klasse: 1 100 MPa (bei Raumtemperatur) /
(à température ambiante) / 315° C 315° C
This European Standard was approved by CEN on 21 June 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4499:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 4499:2009
EN 4499:2009 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Required characteristics .5
3.1 Configuration - Dimensions - Masses .5
3.2 Tolerances of form and position .5
3.3 Materials .5
3.4 Surface treatments .5
4 Designation .8
5 Marking .8
6 Technical specification .9
6.1 General .9
6.2 Approval of manufacturers .9
6.3 Qualification of bolts .9
6.4 Requirement deleted .9
7 Oversized bolts .9
2
---------------------- Page: 4 ----------------------
SIST EN 4499:2009
EN 4499:2009 (E)
Foreword
This document (EN 4499:2009) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at
the latest by August 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxe
...