SIST EN 13445-4:2021/A1:2023

Unfired pressure vessels - Part 4: Fabrication

SIST EN 13445-4:2021/A1:2023

Name:SIST EN 13445-4:2021/A1:2023   Standard name:Unfired pressure vessels - Part 4: Fabrication
Standard number:SIST EN 13445-4:2021/A1:2023   language:English language
Release Date:09-May-2023   technical committee:TLP - Pressure vessels
Drafting committee:   ICS number:23.020.32 - Pressure vessels
SLOVENSKI STANDARD
SIST EN 13445-4:2021/A1:2023
01-junij-2023
Nekurjene tlačne posode - 4. del: Proizvodnja - Dopolnilo A1
Unfired pressure vessels - Part 4: Fabrication
Unbefeuerte Druckbehälter - Teil 4: Herstellung
Récipients sous pression non soumis à la flamme - Partie 4 : Fabrication
Ta slovenski standard je istoveten z: EN 13445-4:2021/A1:2023
ICS:
23.020.32 Tlačne posode Pressure vessels
SIST EN 13445-4:2021/A1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 13445-4:2021/A1:2023

---------------------- Page: 2 ----------------------
SIST EN 13445-4:2021/A1:2023


EN 13445-4:2021/A1
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2023
EUROPÄISCHE NORM
ICS 23.020.30
English Version

Unfired pressure vessels - Part 4: Fabrication
Récipients sous pression non soumis à la flamme - Unbefeuerte Druckbehälter - Teil 4: Herstellung
Partie 4 : Fabrication
This amendment A1 modifies the European Standard EN 13445-4:2021; it was approved by CEN on 3 March 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-4:2021/A1:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 13445-4:2021/A1:2023
EN 13445-4:2021/A1:2023 (E)
Contents Page

European foreword . 3
1 Modification to Clause 2, Normative references . 4
2 Modification to 5.2.2, Identification system . 5
3 Modifications to 7.1, General . 5
4 Modifications to 8.3, Welding procedure qualification record (WPQR) . 5
5 Modifications to 9.4.3, Longitudinal weld tensile test . 6
6 Modification to Bibliography . 6

2

---------------------- Page: 4 ----------------------
SIST EN 13445-4:2021/A1:2023
EN 13445-4:2021/A1:2023 (E)
European foreword
This document (EN 13445-4:2021/A1:2023) has been prepared by Technical Committee CEN/TC 54
“Unfired pressure vessels”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2023, and conflicting national standards shall
be withdrawn at the latest by October 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral part
of EN 13445-4:2021.
This document includes the text of the amendment itself. The amendment will be consolidated within
EN 13445-4:2021 in accordance with the maintenance system of EN 13445 series approved by the
CEN/BT Decis
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27