SIST EN ISO 2439:2009

Flexible cellular polymeric materials - Determination of hardness (indentation technique) (ISO 2439:2008)

SIST EN ISO 2439:2009

Name:SIST EN ISO 2439:2009   Standard name:Flexible cellular polymeric materials - Determination of hardness (indentation technique) (ISO 2439:2008)
Standard number:SIST EN ISO 2439:2009   language:English language
Release Date:02-Apr-2009   technical committee:IPMA - Polimer materials and products
Drafting committee:   ICS number:83.100 - Cellular materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Penjeni polimerni materiali - Mehke pene - Ugotavljanje trdote (odpornost proti vtiskovanju) (ISO 2439:2008)Weich-elastische polymere Schaumstoffe - Bestimmung der Härte (Eindruckverfahren) (ISO 2439:2008)Matériaux polymères alvéolaires souples - Détermination de la dureté (technique par indentation) (ISO 2439:2008)Flexible cellular polymeric materials - Determination of hardness (indentation technique) (ISO 2439:2008)83.100Penjeni polimeriCellular materialsICS:Ta slovenski standard je istoveten z:EN ISO 2439:2008SIST EN ISO 2439:2009en,fr,de01-maj-2009SIST EN ISO 2439:2009SLOVENSKI
STANDARDSIST EN ISO 2439:20011DGRPHãþD



SIST EN ISO 2439:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 2439December 2008ICS 83.100Supersedes EN ISO 2439:2000
English VersionFlexible cellular polymeric materials - Determination of hardness(indentation technique) (ISO 2439:2008)Matériaux polymères alvéolaires souples - Déterminationde la dureté (technique par indentation) (ISO 2439:2008)Weich-elastische polymere Schaumstoffe - Bestimmungder Härte (Eindruckverfahren) (ISO 2439:2008)This European Standard was approved by CEN on 19 November 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 2439:2008: ESIST EN ISO 2439:2009



EN ISO 2439:2008 (E) 2 Contents Page Foreword .3 SIST EN ISO 2439:2009



EN ISO 2439:2008 (E) 3 Foreword This document (EN ISO 2439:2008) has been prepared by Technical Committee ISO/TC 45 "Rubber and rubber products" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2009, and conflicting national standards shall be withdrawn at the latest by June 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 2439:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 2439:2008 has been approved by CEN as a EN ISO 2439:2008 without any modification.
SIST EN ISO 2439:2009



SIST EN ISO 2439:2009



Reference numberISO 2439:2008(E)© ISO 2008
INTERNATIONAL STANDARD ISO2439Fourth edition2008-12-15Flexible cellular polymeric materials — Determination of hardness (indentation technique) Matériaux polymères alvéolaires souples — Détermination de la dureté (technique par indentation)
SIST EN ISO 2439:2009



ISO 2439:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2008 either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
[email protected] Web
www.iso.org Published in Switzerland
ii © ISO 2008 – All rights reserved
SIST EN ISO 2439:2009



ISO 2439:2008(E) © ISO 2008 – All rights reserved iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Terms and definitions.2 4 Principle.2 5 Apparatus.2 6 Test pieces.3 6.1 Shape and dimensions.3 6.2 Samples showing orientation.3 6.3 Conditioning.3 7 Procedure.3 7.1 General.3 7.2 Preliminary indentation for Methods A, B and C.4 7.3 Method A — Determination of the 40 %/30 s indentation hardness index.4 7.4 Method B — Determination of the 25 %-40 %-65 %/30 s indentation hardness characteristics.4 7.5 Method C — Determination of the 40 % indentation hardness check.5 7.6 Method D — Determination of the 25 %/20 s low indentation hardness index.5 7.7 Method E — Determination of the compressive deflection coefficient and hysteresis loss rate.5 8 Repeat tests.7 9 Test report.7 Annex A (informative)
Test method parameters and typical graphs.8 Annex B (informative)
Precision of Method E.12 Bibliography.14
SIST EN ISO 2439:2009



ISO 2439:2008(E) iv © ISO 2008 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2439 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This fourth edition cancels and replaces the third edition (ISO 2439:1997 and ISO 2439:1997/Cor.1:1998), which has been technically revised. Major modifications in this revised text are: a) change in Scope to cover five methods; b) inclusion of Figure 1 to illustrate the force-indentation curve; and c) inclusion of informative annexes.
SIST EN ISO 2439:2009



INTERNATIONAL STANDARD ISO 2439:2008(E) © ISO 2008 – All rights reserved 1Flexible cellular polymeric materials — Determination of hardness (indentation technique) WARNING — Persons using this International Standard should be familiar with normal laboratory practice. This International Standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions. 1 Scope The indentation hardness of flexible cellular materials is a measure of their load-bearing properties. This International Standard specifies four methods (A to D) for the determination of indentation hardness and one method (E) for determination of compressive deflection coefficient and hysteresis loss rate of flexible cellular materials. Annex A provides a summary of test parameters and typical force-indentation graphs obtained with these methods. These five methods are applicable only to latex foam, urethane foam and PVC foam of the open-cell type. The methods specified can be used for testing finished articles and for the characterization of bulk material. This International Standard specifies the following methods: a) Method A — Determination of the 40 %/30 s indentation hardness index, which gives a single indentation measurement for laboratory test purposes; b) Method B — Determination of the 25 %-40 %-65 %/30 s indentation hardness characteristics, which provides information about the shape of the hardness indentation curve; c) Method C — Determination of the 40 % indentation hardness check, which is a quick procedure suitable for quality control testing; d) Method D — Determination of the 25 %/20 s low indentation hardness index, which is a quick procedure suitable as an inspection test; e) Method E — Determination of the compressive deflection coefficient and hysteresis loss rate, which gives additional information about the load-bearing properties of materials. The results obtained by these methods relate only to the test conditions specified and cannot, in general, be used directly for design purposes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1382, Rubber — Vocabulary SIST EN ISO 2439:2009



ISO 2439:2008(E) 2 © ISO 2008 – All rights reserved ISO 7500-1, Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Verification and calibration of the force-measuring system ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test methods 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1382 and the following apply. 3.1 indentation hardness total force required to produce, under specified conditions, a specified indentation of a standard test piece NOTE Indentation hardness is expressed in newtons. 3.2 compressive deflection coefficient Sf ratio of the 65 % indentation force deflection to the 25 % indentation force deflection 3.3 hysteresis loss rate Af energy difference between the loading and unloading of a test piece under cyclic deformation NOTE Hysteresis loss rate is expressed as a percentage of the loading energy. 4 Principle The forces required to produce specified indentations under specified conditions are measured. 5 Apparatus 5.1 Test machine. The test machine shall be capable of indenting the test piece between a supporting surface (5.2) and an indentor (5.3) having a uniform relative motion, in the vertical direction, of (100 ± 20) mm/min. The test machine shall have means of measuring force in conformance with Class 1 of ISO 7500-1 or of measuring with a precision of ± 1 N, and of measuring the test piece thickness under
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27