|
SIST EN ISO 26443:2016
01-junij-2016
1DGRPHãþD
SIST-TS CEN/TS 1071-8:2005
)LQDNHUDPLNDVRGREQDNHUDPLNDVRGREQDWHKQLþQDNHUDPLND3UHVNXV]
YWLVNDQMHPSR5RFNZHOOX]DRYUHGQRWHQMHVSULMHPQRVWLNHUDPLþQLKSUHYOHN,62
Fine ceramics (advanced ceramics, advanced technical ceramics) - Rockwell indentation
test for evaluation of adhesion of ceramic coatings (ISO 26443:2008)
Hochleistungskeramik - Rockwell-Eindringprüfung zur Bewertung der Haftung von
keramischen Schichten (ISO 26443:2008)
Céramiques techniques - Évaluation de l'adhérence des revêtements céramiques par
l'essai de pénétration de Rockwell (ISO 26443:2008)
Ta slovenski standard je istoveten z: EN ISO 26443:2016
ICS:
25.220.99 Druge obdelave in prevleke Other treatments and
coatings
81.060.30 Sodobna keramika Advanced ceramics
SIST EN ISO 26443:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 26443:2016
---------------------- Page: 2 ----------------------
SIST EN ISO 26443:2016
EN ISO 26443
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2016
EUROPÄISCHE NORM
ICS 81.060.30 Supersedes CEN/TS 1071-8:2004
English Version
Fine ceramics (advanced ceramics, advanced technical
ceramics) - Rockwell indentation test for evaluation of
adhesion of ceramic coatings (ISO 26443:2008)
Céramiques techniques - Évaluation de l'adhérence des Hochleistungskeramik - Rockwell-Eindringprüfung zur
revêtements céramiques par l'essai de pénétration Bewertung der Haftung von keramischen Schichten
Rockwell (ISO 26443:2008) (ISO 26443:2008)
This European Standard was approved by CEN on 18 March 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 26443:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 26443:2016
EN ISO 26443:2016 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 26443:2016
EN ISO 26443:2016 (E)
European foreword
The text of ISO 26443:2008 has been prepared by Technical Committee ISO/TC 206 “Fine ceramics” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 26443:2016
by Technical Committee CEN/TC 184 “Advanced technical ceramics” the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2016, and conflicting national standards shall
be withdrawn at the latest by October 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes CEN/TS 1071-8:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 26443:2008 has been a
...