|
SIST EN 3475-417:2009
01-junij-2009
$HURQDYWLND(OHNWULþQLNDEOL]DXSRUDERY]UDþQLKSORYLOLK3UHVNXVQHPHWRGH
GHO3RåDUQDRGSRUQRVWNDEORYYVQRSLK
Aerospace series - Cables, electrical, aircraft use - Test methods - Part 417: Fire
resistance of cables confined inside a harness
Luft- und Raumfahrt - Elektrischen Leitungen für Luftfahrt Verwendung - Prüfverfahren -
Teil 417: Feuerbeständigkeit von Leitungen eingebunden in Bündeln
Série aérospatiale - Câbles électriques à usage aéronautique - Méthodes d'essais -
Partie 417: Tenue au feu des câbles confinés dans un harnais
Ta slovenski standard je istoveten z: EN 3475-417:2009
ICS:
49.060 /HWDOVNDLQYHVROMVND Aerospace electric
HOHNWULþQDRSUHPDLQVLVWHPL equipment and systems
SIST EN 3475-417:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 3475-417:2009
---------------------- Page: 2 ----------------------
SIST EN 3475-417:2009
EUROPEAN STANDARD
EN 3475-417
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2009
ICS 49.060
English Version
Aerospace series - Cables, electrical, aircraft use - Test
methods - Part 417: Fire resistance of cables confined inside a
harness
Série aérospatiale - Câbles électriques à usage Luft- und Raumfahrt - Elektrischen Leitungen für Luftfahrt
aéronautique - Méthodes d'essais - Partie 417: Tenue au Verwendung - Prüfverfahren - Teil 417: Feuerbeständigkeit
feu des câbles confinés dans un harnais von Leitungen eingebunden in Bündeln
This European Standard was approved by CEN on 30 August 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3475-417:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 3475-417:2009
EN 3475-417:2009 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Preparation of specimens .4
4 Apparatus .4
5 Method .5
6 Requirements/Acceptance criteria .6
Annex A (normative) Circuit diagram principle for measurement of equipotentials .7
2
---------------------- Page: 4 ----------------------
SIST EN 3475-417:2009
EN 3475-417:2009 (E)
Foreword
This document (EN 3475-417:2009) has been prepared by the Aerospace and Defence Industries Association
of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2009, and conflicting national standards shall be
withdrawn at the latest by September 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations
...