|
SIST EN 1010-5:2005
01-september-2005
9DUQRVWVWURMHY±9DUQRVWQH]DKWHYH]DQDþUWRYDQMHLQNRQVWUXNFLMRWLVNDUVNLK
VWURMHYLQVWURMHY]DREGHODYRSDSLUMD±GHO6WURML]DL]GHODYRYDORYLWHJDNDUWRQD
LQOHSHQNHLQVWURML]DREGHODYRSORVNHJDLQYDORYLWHJDNDUWRQDLQOHSHQNH
Safety of machinery - Safety requirements for the design and construction of printing and
paper converting machines - Part 5: Machines for the production of corrugated board and
machines for the conversion of flat and corrugated board
Sicherheit von Maschinen - Sicherheitsanforderungen an Konstruktion und Bau von
Druck- und Papierverarbeitungsmaschinen - Wellpappenerzeugungs-, Flach- und
Wellpappenverarbeitungsmaschinen
Sécurité des machines - Prescriptions de sécurité pour la conception et la construction
de machines d'impression et de transformation du papier - Partie 5: Machines de
fabrication du carton ondulé et machines de transformation du carton plat et du carton
ondulé
Ta slovenski standard je istoveten z: EN 1010-5:2005
ICS:
37.100.10 Reprodukcijska oprema Reproduction equipment
85.100 Oprema za papirno industrijo Equipment for the paper
industry
SIST EN 1010-5:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 1010-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2005
ICS 85.100
English version
Safety of machinery - Safety requirements for the design and
construction of printing and paper converting machines - Part 5:
Machines for the production of corrugated board and machines
for the conversion of flat and corrugated board
Sécurité des machines - Prescriptions de sécurité pour la Sicherheit von Maschinen - Sicherheitsanforderungen an
conceptions des machines d'impression, de transformation Konstruktion und Bau von Druck- und
et définition du papier - Partie 5: Onduleuses et machines Papierverarbeitungsmaschinen - Wellpappenerzeugungs-,
de trasformation du carton plat et du carton ondulé Flach- und Wellpappenverarbeitungsmaschinen
This European Standard was approved by CEN on 2 September 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1010-5:2005: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 1010-5:2005 (E)
Contents Page
Foreword .4
Introduction.5
1 Scope.5
2 Normative references.6
3 Terms and definitions .6
4 List of significant hazards.8
5 Safety requirements and/or measures .13
5.1 General.13
5.2 Machines for the production of corrugated board.13
5.2.1 Entire machines.
...