SIST ISO 12643-5:2011

Graphic technology - Safety requirements for graphic technology equipment and systems - Part 5: Stand-alone platen presses

SIST ISO 12643-5:2011

Name:SIST ISO 12643-5:2011   Standard name:Graphic technology - Safety requirements for graphic technology equipment and systems - Part 5: Stand-alone platen presses
Standard number:SIST ISO 12643-5:2011   language:English language
Release Date:30-May-2011   technical committee:GRT - Graphical technology
Drafting committee:   ICS number:37.100.10 - Reproduction equipment
SLOVENSKI STANDARD
SIST ISO 12643-5:2011
01-julij-2011
*UDILþQDWHKQRORJLMD9DUQRVWQH]DKWHYH]DJUDILþQRWHKQRORãNRRSUHPRLQ
VLVWHPHGHO6DPRVWRMQL]DNORSQLVWURML
Graphic technology - Safety requirements for graphic technology equipment and systems
- Part 5: Stand-alone platen presses
Technologie graphique — Exigences de sécurité pour les systèmes et l'équipement de
technologie graphique — Partie 5: Presses à plateaux autonomes
Ta slovenski standard je istoveten z: ISO 12643-5:2010
ICS:
37.100.10 Reprodukcijska oprema Reproduction equipment
SIST ISO 12643-5:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 12643-5:2011

---------------------- Page: 2 ----------------------

SIST ISO 12643-5:2011

INTERNATIONAL ISO
STANDARD 12643-5
First edition
2010-12-15

Graphic technology — Safety
requirements for graphic technology
equipment and systems —
Part 5:
Stand-alone platen presses
Technologie graphique — Exigences de sécurité pour les systèmes
et l'équipement de technologie graphique —
Partie 5: Presses à plateaux autonomes




Reference number
ISO 12643-5:2010(E)
©
ISO 2010

---------------------- Page: 3 ----------------------

SIST ISO 12643-5:2011
ISO 12643-5:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 12643-5:2011
ISO 12643-5:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 Safeguarding of significant hazards .2
4.1 General .2
4.2 Additional safeguarding requirements .2
4.3 Safeguarding side access .3
4.4 Additional requirements for manually fed platen presses.4
4.5 Laser scanners .7
4.6 Platen presses with automatic (timer-controlled) operation .7
4.7 Stopping distance .7
4.8 Main drive braking and clutch/brake mechanism .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27