|
STANDARD
SIST EN 2436-006:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2436-006July 2006ICS 49.040 English VersionAerospace series - Paints and varnishes - Corrosion resistantchromate-free two component cold curing epoxy primer - Part006: High corrosion resistance for military applicationSérie aérospatiale - Peintures primaire anti-corrosion sanschromate à deux composants polymérisant à températureambiante - Partie 006 : Haute résistance à la corrosionpour applications militairesLuft- und Raumfahrt - Anstrichstoffe -Korrosionsbeständiger Zweikomponenten-Grundanstrich,kalthärtend chromatfrei - Teil 006: Hoher Korrosionsschutzfür militärische AnwendungThis European Standard was approved by CEN on 27 February 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2436-006:2006: ESIST EN 2436-006:2009
EN 2436-006:2006 (E) 2 Contents Page Foreword.3 0 Introduction.4 1 Scope.4 2 Normative references.4 3 Definitions.5 4 Classification.6 5 Batch release and qualification testing.6 6 Designation.14 7 Requirements for fibre reinforced composites.14
SIST EN 2436-006:2009
EN 2436-006:2006 (E) 3 Foreword This European Standard (EN 2436-006:2006) has been prepared by the AeroSpace and Defense Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re-ceived the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2007, and conflicting national standards shall be withdrawn at the latest by January 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Den-mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem-bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer-land and the United Kingdom. SIST EN 2436-006:2009
EN 2436-006:2006 (E) 4 0 Introduction The requirements concerning fibre reinforced composite substrates are established in Clause 7. 1 Scope This standard defines the requirements for a two component, chromate and lead free epoxy, high corrosion resistant primer. The coating shall be suitable for use on chromic acid anodised or conversion coated aluminium alloys, fibre reinforced composite materials and other suitably prepared substrates. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer-ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including amendments) applies. EN 2435-005, Aerospace series — Paints and varnishes — Corrosion resistant chromated two component cold curing epoxy primer — Part 005: High corrosion resistance for military application1) EN 3212, Aerospace series — Paints and varnishes — Corrosion test by alternate immersion in a buffered sodium chloride solution EN 3837, Aerospace series — Paints and varnishes — Nature and method for surface preparation of test pieces in aluminium alloys1) EN 3840, Aerospace series — Paints and varnishes — Technical specification1) EN 3847, Aerospace series — Paints and varnishes — Determination of sedimentation rating1) EN 4160, Aerospace series — Non-metallic materials — Paints and varnishes — Test methods — Determina-tion of the effects of thermal exposure1) ISO 1513, Paints and varnishes — Examination and preparation of samples for testing ISO 1517, Paints and varnishes — Surface-drying test — Ballotini method ISO 1518, Paints and varnishes — Scratch test ISO 1519, Paints and varnishes — Bend test (cylindrical mandrel) ISO 1520, Paints and varnishes — Cupping test ISO 1524, Paints, varnishes and printing inks — Determination of fineness of grind ISO 2409, Paints and varnishes — Cross-cut test ISO 2431, Paints and varnishes — Determination of flow time by use of flow cups ISO 2811-1, Paints and varnishes — Determination of density — Part 1: Pyknometer method ISO 2811-2, Paints and varnishes — Determination of density — Part 2: Immersed body (plummet) method ISO 2811-3, Paints and varnishes — Determination of density — Part 3: Oscillation method
1) Published as ASD Prestandard at the date of publication of this standard. SIST EN 2436-006:2009
EN 2436-006:2006 (E) 5 ISO 2811-4, Paints and varnishes — Determination of density — Part 4: Pressure cup method ISO 2812-1, Paints and varnishes — Determination of resistance to liquids — Part 1: General methods ISO 2812-2, Paints and varnishes — Determination of resistance to liquids — Part 2: Water immersion method ISO 3251, Paints, varnishes and plastics — Determination of non-volatile-matter content ISO 3270, Paints and varnishes and their raw materials — Temperatures and humidities for conditioning and testing ISO 3675, Crude petroleum and liquid petroleum products — Laboratory determination of density — Hy-drometer method ISO 3678, Paints and varnishes — Print-free test ISO 3679, Determination of flash point — Rapid equilibrium closed cup method ISO 3680, Determination of flash/no flash — Rapid equilibrium closed cup method ISO 4623-2, Paints and varnishes — Determination of resistance to filiform corrosion — Part 2: Aluminium substrates ISO 4628-2, Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 2: Assessment of degree of blistering ISO 4628-8, Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 8: Assessment of degree of delamina-tion and corrosion around the scribe ISO 4628-10, Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 10: Assessment of degree of filiform corrosion ISO 6270-1, Paints and varnishes — Determination of resistance to humidity — Part 1: Continuous condensa-tion ISO 7253, Paints and varnishes — Determination of resistance to neutral salt spray (fog) ISO 7724-1, Paints and varnishes — Colorimetry — Part 1: Principles ISO 7724-2, Paints and varnishes — Colorimetry — Part 2: Colour measurement ISO 7724-3, Paints and varnishes — Colorimetry — Part 3: Calculation of colour differences ISO 9117, Paints and varnishes —– Determination of through-dry state and through-dry time — Method of test ISO 9514, Paints and varnishes — Determination of the pot-life of multicomponent coating systems — Prepa-ration and conditioning of samples and guidelines for testing ISO 11890-1, Paints and varnishes — Determination of volatile organic compound (VOC) content — Part 1: Dif-ference method ISO 11890-2, Paints and varnishes — Determination of volatile organic compound (VOC) content — Part 2: Gas-chromatographic method 3 Definitions
...