|
SIST EN 2516:2020
01-marec-2020
Nadomešča:
SIST EN 2516:2001
Aeronavtika - Pasiviranje korozijsko odpornih jekel in dekontaminacija nikljevih
zlitin
Aerospace series - Passivation of corrosion resisting steels and decontamination of
nickel base alloys
Luft- und Raumfahrt - Passivieren von korrosionsbeständigen Stählen und
Dekontaminierung von Nickellegierungen
Série aérospatiale - Passivation des aciers résistants à la corrosion et décontamination
des alliages base nickel
Ta slovenski standard je istoveten z: EN 2516:2020
ICS:
49.040 Prevleke in z njimi povezani Coatings and related
postopki, ki se uporabljajo v processes used in aerospace
letalski in vesoljski industriji industry
SIST EN 2516:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 2516:2020
---------------------- Page: 2 ----------------------
SIST EN 2516:2020
EN 2516
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2020
EUROPÄISCHE NORM
ICS 49.040 Supersedes EN 2516:1997
English Version
Aerospace series - Passivation of corrosion resisting steels
and decontamination of nickel base alloys
Série aérospatiale - Passivation des aciers résistants à Luft- und Raumfahrt - Passivieren von
la corrosion et décontamination des alliages base korrosionsbeständigen Stählen und Dekontaminierung
nickel von Nickellegierungen
This European Standard was approved by CEN on 11 November 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2516:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 2516:2020
EN 2516:2020 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Purpose of process . 4
5 Applicability and limitations of the process . 4
6 Information for the processor . 5
7 Condition of the parts prior to processing . 5
8 Pre-treatments . 5
9 Treatment . 6
10 Required characteristics and inspections. 7
11 Quality assurance . 8
12 Health, safety and environme
...