|
SIST EN ISO 3882:2003
01-december-2003
1DGRPHãþD
SIST EN ISO 3882:1999
Kovinske in druge anorganske prevleke - Pregled metod za merjenje debeline (ISO
3882:2003)
Metallic and other inorganic coatings - Review of methods of measurement of thickness
(ISO 3882:2003)
Metallische und andere anorganische Überzüge - Übersicht über Verfahren zur
Schichtdickenmessung (ISO 3882:2003)
Revetements métalliques et autres revetements inorganiques - Vue d'ensemble sur les
méthodes de mesurage de l'épaisseur (ISO 3882:2003)
Ta slovenski standard je istoveten z: EN ISO 3882:2003
ICS:
17.040.20 Lastnosti površin Properties of surfaces
25.220.40 Kovinske prevleke Metallic coatings
SIST EN ISO 3882:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 3882:2003
---------------------- Page: 2 ----------------------
SIST EN ISO 3882:2003
EUROPEAN STANDARD
EN ISO 3882
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2003
ICS 25.220.20; 25.220.40 Supersedes EN ISO 3882:1994
English version
Metallic and other inorganic coatings - Review of methods of
measurement of thickness (ISO 3882:2003)
Revêtements métalliques et autres revêtements Metallische und andere anorganische Überzüge - Übersicht
inorganiques - Vue d'ensemble sur les méthodes de über Verfahren zur Schichtdickenmessung (ISO
mesurage de l'épaisseur (ISO 3882:2003) 3882:2003)
This European Standard was approved by CEN on 21 March 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3882:2003 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 3882:2003
EN ISO 3882:2003 (E)
CORRECTED 2003-07-16
Foreword
This document (EN ISO 3882:2003) has been prepared by Technical Committee ISO/TC 107
"Metallic and other inorganic coatings" in collaboration with Technical Committee CEN/TC 262
"Metallic and other inorganic coatings", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by October 2003, and conflicting national
standards shall be withdrawn at the latest by October 2003.
This document supersedes EN ISO 3882:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
Endorsement notice
The text of ISO 3882:2003 has been approved by CEN as EN ISO 3882:2003 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2
---------------------- Page: 4 ----------------------
SIST EN ISO 3882:2003
EN ISO 3882:2003 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 1463 1982 Metallic and oxide coatings - EN ISO 1463 1994
Measurement of c
...