|
SIST EN ISO 9012:2011
01-december-2011
1DGRPHãþD
SIST EN 731:1997
2SUHPD]DSODPHQVNRYDUMHQMH5RþQLJRULOQLNL]YVHVDYDQMHP]UDND3RSLVLLQ
SUHVNXVL,62
Gas welding equipment - Air-aspirated hand blowpipes - Specifications and tests (ISO
9012:2008)
Gasschweißgeräte - Handbrenner für angesaugte Luft - Anforderungen und Prüfungen
(ISO 9012:2008)
Équipement de soudage aux gaz - Chalumeaux manuels aéro-gaz à air aspiré -
Spécifications et essais (ISO 9012:2008)
Ta slovenski standard je istoveten z: EN ISO 9012:2011
ICS:
25.160.30 Varilna oprema Welding equipment
SIST EN ISO 9012:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 9012:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 9012:2011
EUROPEAN STANDARD
EN ISO 9012
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2011
ICS 25.160.30 Supersedes EN 731:1995
English Version
Gas welding equipment - Air-aspirated hand blowpipes -
Specifications and tests (ISO 9012:2008)
Équipement de soudage aux gaz - Chalumeaux manuels Gasschweißgeräte - Handbrenner für angesaugte Luft -
aéro-gaz à air aspiré - Spécifications et essais (ISO Anforderungen und Prüfungen (ISO 9012:2008)
9012:2008)
This European Standard was approved by CEN on 18 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9012:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 9012:2011
EN ISO 9012:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 9012:2011
EN ISO 9012:2011 (E)
Foreword
The text of ISO 9012:2008 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
9012:2011 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the
latest by April 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 731:1995.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 9012:2008 has been approved by CEN as a EN ISO 9012:2011 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 9012:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 9012:2011
INTERNATIONAL ISO
STANDARD 9012
Third edition
2008-02-15
Gas welding equipment — Air-aspirated
hand blowpipes — Specifications and
tests
Équipement de soudage aux gaz — Chalumeaux manuels aéro-gaz à
air aspiré — Spécifications et
...