|
SIST-TS CEN/TS 16637-2:2014
01-november-2014
*UDGEHQLSURL]YRGL2FHQMHYDQMHVSURãþDQMDQHYDUQLKVQRYLGHO+RUL]RQWDOQL
GLQDPLþQLSUHVNXV]DL]OXåHYDQMHVSRYUãLQH
Construction products - Assessment of release of dangerous substances - Part 2:
Horizontal dynamic surface leaching test
Bauprodukte - Bewertung der Freisetzung von gefährlichen Stoffen - Teil 2: Horizontale
dynamische Oberflächenauslaugprüfung
Produits de construction - Evaluation de l‘émission de substances dangereuses - Partie
2: Essais horizontaux et dynamiques de la lixivation des surfaces
Ta slovenski standard je istoveten z: CEN/TS 16637-2:2014
ICS:
13.020.99 Drugi standardi v zvezi z Other standards related to
varstvom okolja environmental protection
91.100.01 Gradbeni materiali na Construction materials in
splošno general
SIST-TS CEN/TS 16637-2:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 16637-2:2014
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 16637-2:2014
TECHNICAL SPECIFICATION
CEN/TS 16637-2
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
August 2014
ICS 13.040.20; 19.040; 91.100.01
English Version
Construction products - Assessment of release of dangerous
substances - Part 2: Horizontal dynamic surface leaching test
Produits de construction - Evaluation de l'émission de Bauprodukte - Bewertung der Freisetzung von gefährlichen
substances dangereuses - Partie 2: Essais horizontaux et Stoffen - Teil 2: Horizontale dynamische
dynamiques de la lixivation des surfaces Oberflächenauslaugprüfung
This Technical Specification (CEN/TS) was approved by CEN on 25 February 2014 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 16637-2:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 16637-2:2014
CEN/TS 16637-2:2014 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .7
2 Normative references .7
3 Terms and definitions .8
4 Symbols and abbreviations . 11
5 Principle . 12
6 Reagents . 13
7 Equipment . 13
8 Sample preparation . 14
8.1 General .
...