|
SIST-TS CEN/TS 16637-3:2017
01-marec-2017
*UDGEHQLSURL]YRGL2FHQMHYDQMHVSURãþDQMDQHYDUQLKVQRYLGHO +RUL]RQWDQL
SUHVNXVSUHFHMDQMDYNRORQLVWRNRPQDY]JRU
Construction products - Assessment of release of dangerous substances - Part 3:
Horizontal up-flow percolation test
Bauprodukte - Bewertung der Freisetzung von gefährlichen Stoffen - Teil 3: Horizontale
Perkolationsprüfung im Aufwärtsstrom
Produits de construction - Evaluation de l’émission de substances dangereuses - Partie
3 : Essai horizontal de percolation à l’écoulement ascendant
Ta slovenski standard je istoveten z: CEN/TS 16637-3:2016
ICS:
13.020.99 Drugi standardi v zvezi z Other standards related to
varstvom okolja environmental protection
91.100.01 Gradbeni materiali na Construction materials in
splošno general
SIST-TS CEN/TS 16637-3:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 16637-3:2017
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 16637-3:2017
CEN/TS 16637-3
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
June 2016
TECHNISCHE SPEZIFIKATION
ICS 19.040; 13.040.20; 91.100.01
English Version
Construction products - Assessment of release of
dangerous substances - Part 3: Horizontal up-flow
percolation test
Produits de construction - Evaluation de l'émission de Bauprodukte - Bewertung der Freisetzung von
substances dangereuses - Partie 3 : Essai horizontal de gefährlichen Stoffen - Teil 3: Horizontale
percolation à l'écoulement ascendant Perkolationsprüfung im Aufwärtsstrom
This Technical Specification (CEN/TS) was approved by CEN on 15 March 2016 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 16637-3:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 16637-3:2017
CEN/TS 16637-3:2016 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 Symbols and abbreviations . 10
4.1 Symbols . 10
4.2 Abbreviations . 11
5 Principle . 11
6 Reagents . 12
7 Equipment .
...