|
SIST-TS CEN/TS 16637-1:2019
01-marec-2019
1DGRPHãþD
SIST-TS CEN/TS 16637-1:2014
*UDGEHQLSURL]YRGL2FHQMHYDQMHVSURãþDQMDQHYDUQLKVQRYLGHO1DYRGLOR]D
GRORþDQMHSUHVNXVRYL]OXåHYDQMDLQGRGDWQLKNRUDNRYSUHVNXãDQMD
Construction products - Assessment of release of dangerous substances - Part 1:
Guidance for the determination of leaching tests and additional testing steps
Bauprodukte - Bewertung der Freisetzung von gefährlichen Stoffen - Teil 1: Leitfaden für
die Festlegung von Auslaugprüfungen und zusätzlichen Prüfschritten
Produits de construction - Evaluation de l'émission de substances dangereuses - Partie
1 : Guide pour la spécification des essais de lixiviation et des étapes supplémentaires
d'essai
Ta slovenski standard je istoveten z: CEN/TS 16637-1:2018
ICS:
13.020.99 Drugi standardi v zvezi z Other standards related to
varstvom okolja environmental protection
91.100.01 Gradbeni materiali na Construction materials in
splošno general
SIST-TS CEN/TS 16637-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 16637-1:2019
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 16637-1:2019
CEN/TS 16637-1
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
October 2018
TECHNISCHE SPEZIFIKATION
ICS 19.040; 13.040.20; 91.100.01
English Version
Construction products - Assessment of release of
dangerous substances - Part 1: Guidance for the
determination of leaching tests and additional testing
steps
Produits de construction - Evaluation de l'émission de Bauprodukte - Bewertung der Freisetzung von
substances dangereuses - Partie 1 : Guide pour la gefährlichen Stoffen - Teil 1: Leitfaden für die
spécification des essais de lixiviation et des étapes Festlegung von Auslaugprüfungen und zusätzlichen
supplémentaires d'essai Prüfschritten
This Technical Specification (CEN/TS) was approved by CEN on 13 May 2018 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 16637-1:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 16637-1:2019
CEN/TS 16637-1:2018 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
3.1 Sampling and products . 7
3.2 Release and laboratory testing . 10
4 Symbols and abbreviations . 14
5 Determination of the appropriate release test method .
...