SIST EN 15865:2009

Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993 modified)

SIST EN 15865:2009

Name:SIST EN 15865:2009   Standard name:Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993 modified)
Standard number:SIST EN 15865:2009   language:English language
Release Date:09-Jun-2009   technical committee:IPMA - Polimer materials and products
Drafting committee:   ICS number:83.180 - Adhesives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Klebstoffe - Bestimmung der Drehfestigkeit von anaeroben Klebstoffen auf geklebten Gewinden (ISO 10964:1993 modifiziert)Adhésifs - Détermination des couples fonctionnels sur des fixations filetées collées avec des adhésifs anaérobies (ISO 10964:1993 modifiée)Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993 modified)83.180LepilaAdhesivesICS:Ta slovenski standard je istoveten z:EN 15865:2009SIST EN 15865:2009en,fr,de01-julij-2009SIST EN 15865:2009SLOVENSKI
STANDARDSIST EN ISO 10964:19981DGRPHãþD



SIST EN 15865:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15865April 2009ICS 83.180Supersedes EN ISO 10964:1997
English VersionAdhesives - Determination of torque strength of anaerobicadhesives on threaded fasteners (ISO 10964:1993 modified)Adhésifs - Détermination des couples fonctionnels sur desfixations filetées collées avec des adhésifs anaérobies (ISO10964:1993 modifiée)Klebstoffe - Bestimmung der Drehfestigkeit von anaerobenKlebstoffen auf geklebten Gewinden (ISO 10964:1993modifiziert)This European Standard was approved by CEN on 26 March 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15865:2009: ESIST EN 15865:2009



EN 15865:2009 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .4 4 Principle .6 5 Apparatus .6 6 Test specimens .8 7 Application of adhesive .8 8 Assembly .9 9 Test procedure . 10 10 Precision . 10 11 Test report . 11 Bibliography . 12
SIST EN 15865:2009



EN 15865:2009 (E) 3 Foreword This document (EN 10964:2009) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10964:1997. Safety statement Persons using this document should be familiar with the normal laboratory practice, if applicable. This document cannot address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any regulatory conditions. Environmental statement It is understood that some of the material permitted in this standard may have negative environmental impact. As technological advantages lead to better alternatives for these materials, they will be eliminated from this standard to the extent possible. At the end of the test, the user of the standard shall take care to carry out an appropriate disposal of the wastes, according to local regulation. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 15865:2009



EN 15865:2009 (E) 4 1 Scope The test method described in this European Standard is used to make comparative assessments of the securing or locking effect of anaerobic adhesives used in threaded assemblies. This method may be used for other types of adhesives, if considered suitable.
2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 20898-2, Mechanical properties of fasteners - Part 2: Nuts with specified proof load values – Coarse thread (ISO 898-2:1992) EN ISO 291, Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008) EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2009) 3 Terms and definitions
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27