SIST EN 4424:2009

Aerospace series - Rod-ends, adjustable, single fork and threaded shank with engagement: 1,5 × thread diameter in titanium alloys - Dimensions and loads

SIST EN 4424:2009

Name:SIST EN 4424:2009   Standard name:Aerospace series - Rod-ends, adjustable, single fork and threaded shank with engagement: 1,5 × thread diameter in titanium alloys - Dimensions and loads
Standard number:SIST EN 4424:2009   language:English language
Release Date:11-Jun-2009   technical committee:I13 - Imaginarni 13
Drafting committee:   ICS number:49.035 - Components for aerospace construction
SLOVENSKI STANDARD
SIST EN 4424:2009
01-julij-2009
$HURQDYWLND.RQþQLNLQDVWDYOMLYLHQRVWDYQL]QDYRMQLPVWHEORPLQJORELQR
YLMDþHQMDîQDYRMQLSUHPHUL]WLWDQRYLK]OLWLQ0HUHLQQRVLOQRVWL
Aerospace series - Rod-ends, adjustable, single fork and threaded shank with
engagement: 1,5 × thread diameter in titanium alloys - Dimensions and loads
Luft- und Raumfahrt - Einstellbare Gabelköpfe, einfach, mit Gewindeschaft mit einer
Einschraubtiefe von 1,5 × Gewindedurchmesser, aus Titanlegierungen - Maße und
Belastungen
Série aérospatiale - Embouts réglables à chape simple et à tige filetée à implantation :
1,5 × diamètre filetage en alliages de titane - Dimensions et charges
Ta slovenski standard je istoveten z: EN 4424:2006
ICS:
49.035 Sestavni deli za letalsko in Components for aerospace
vesoljsko gradnjo construction
SIST EN 4424:2009 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 4424:2009

---------------------- Page: 2 ----------------------

SIST EN 4424:2009
EUROPEAN STANDARD
EN 4424
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2006
ICS 49.035

English Version
Aerospace series - Rod-ends, adjustable, single fork and
threaded shank with engagement: 1,5 × thread diameter in
titanium alloys - Dimensions and loads
Série aérospatiale - Embouts réglables à chape simple et à Luft- und Raumfahrt - Einstellbare Gabelköpfe, einfach, mit
tige filetée à implantation : 1,5 × diamètre filetage en Gewindeschaft mit Einschraubtiefe 1,5 ×
alliages de titane - Dimensions et charges Gewindedurchmesseraus Titanlegierungen - Maße und
Belastungen
This European Standard was approved by CEN on 20 April 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4424:2006: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 4424:2009
EN 4424:2006 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Required characteristics.4
4 Designation .6
5 Marking .7
6 Technical specification .7

2

---------------------- Page: 4 ----------------------

SIST EN 4424:2009
EN 4424:2006 (E)
Foreword
This European Standard (EN 4424:2006) has been prepared by the European Association of Aerospace
Manufacturers - Standardization (AECMA-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
AECMA, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2006, and conflicting national standards shall be with
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27