SIST EN 2624:2009

Aerospace series - Pressure impulse testing of hydraulic system components

SIST EN 2624:2009

Name:SIST EN 2624:2009   Standard name:Aerospace series - Pressure impulse testing of hydraulic system components
Standard number:SIST EN 2624:2009   language:English language
Release Date:22-Jun-2009   technical committee:I13 - Imaginarni 13
Drafting committee:   ICS number:49.080 - Aerospace fluid systems and components
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Druckimpulsprüfung von Komponenten in Hydraulik-AnlagenSérie aérospatiale - Essai d'impulsion de pression des composants de systèmes hydrauliquesAerospace series - Pressure impulse testing of hydraulic system components49.080Aerospace fluid systems and componentsICS:Ta slovenski standard je istoveten z:EN 2624:2007SIST EN 2624:2009en,de01-september-2009SIST EN 2624:2009SLOVENSKI
STANDARD



SIST EN 2624:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2624July 2007ICS 49.080 English VersionAerospace series - Pressure impulse testing of hydraulic systemcomponentsSérie aérospatiale - Essai d'impulsion de pression descomposants de systèmes hydrauliquesLuft- und Raumfahrt - Druckimpulsprüfung vonKomponenten in Hydraulik-AnlagenThis European Standard was approved by CEN on 13 April 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2624:2007: ESIST EN 2624:2009



EN 2624:2007 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Requirements.5 4.1 General.5 4.2 Rate of rise.5 4.3 Cycling rate.5 4.4 Temperature.5 4.5 Number of cycles.5 4.6 Preparation of specimens.6 4.7 Test equipment.6 4.8 Test fluid.6 4.9 Performance after test.6 5 Test procedure.6 5.1 General.6 5.2 Accuracy.6 5.3 Component set-up.6 5.4 Impulse test.6 5.5 Component verification.6
SIST EN 2624:2009



EN 2624:2007 (E) 3 Foreword This document (EN 2624:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2008, and conflicting national standards shall be withdrawn at the latest by January 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germa
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27