SIST EN ISO 9117-1:2009

Paints and varnishes - Determination of through-dry state and through-dry time - Method of test (ISO 9117-1:2009)

SIST EN ISO 9117-1:2009

Name:SIST EN ISO 9117-1:2009   Standard name:Paints and varnishes - Determination of through-dry state and through-dry time - Method of test (ISO 9117-1:2009)
Standard number:SIST EN ISO 9117-1:2009   language:English language
Release Date:13-Jul-2009   technical committee:IBLP - Paints and varnishes
Drafting committee:   ICS number:87.040 - Paints and varnishes
SLOVENSKI STANDARD
SIST EN ISO 9117-1:2009
01-september-2009
1DGRPHãþD
SIST EN 29117:1997
%DUYHLQODNL'RORþDQMHXWUMHQHJDVWDQMDLQþDVDXWUMHYDQMD3UHVNXVQDPHWRGD
,62
Paints and varnishes - Determination of through-dry state and through-dry time - Method
of test (ISO 9117-1:2009)
Beschichtungsstoffe - Bestimmung des Durchtrocknungszustandes und der
Durchtrocknungszeit - Prüfverfahren (ISO 9117-1:2009)
Peintures et vernis - Détermination du séchage à coeur et du temps de séchage à coeur
- Méthode d'essai (ISO 9117-1:2009)
Ta slovenski standard je istoveten z: EN ISO 9117-1:2009
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 9117-1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 9117-1:2009

---------------------- Page: 2 ----------------------

SIST EN ISO 9117-1:2009
EUROPEAN STANDARD
EN ISO 9117-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2009
ICS 87.040 Supersedes EN 29117:1992
English Version
Paints and varnishes - Drying tests - Part 1: Determination of
through-dry state and through-dry time (ISO 9117-1:2009)
Peintures et vernis - Essais de séchage - Partie 1: Beschichtungsstoffe - Trocknungsprüfungen - Teil 1:
Détermination du séchage à coeur et du temps de séchage Bestimmung des Durchtrocknungszustandes und der
à coeur (ISO 9117-1:2009) Durchtrocknungszeit (ISO 9117-1:2009)
This European Standard was approved by CEN on 23 April 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9117-1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 9117-1:2009
EN ISO 9117-1:2009 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 9117-1:2009
EN ISO 9117-1:2009 (E)
Foreword
This document (EN ISO 9117-1:2009) has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2009, and conflicting national standards shall be withdrawn
at the latest by November 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 29117:1992.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 9117-1:2009 has been approved by CEN as a EN ISO 9117-1:2009 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 9117-1:2009

---------------------- Page: 6 ----------------------

SIST EN ISO 9117-1:2009

INTERNATIONAL ISO
STANDARD 9117-1
First edition
2009-05-15


Paints and varnishes — Drying tests —
Part 1:
Determination of through-dry state
and through-dry time
Peintures et vernis — Essais de séchage —
Partie 1: Détermination du séchage à cœur et du temps de séchage
à cœur





Reference number
ISO 9117-1:2009(E)
©
ISO 2009

---------------------- Page: 7 ----------------------

SIST EN ISO 9117-1:2009
ISO 9117-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 9117-1:2009
ISO 9117-1:2009(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 1
4 Principle. 2
5 Apparatus and materials. 2
6 Sampling. 4
7 Test panels . 4
7.1 Substrate . 4
7.2 Preparation and coating. 4
8 Procedure . 5
8.1 Preparation of apparatus . 5
8.2 Drying the test panel . 5
8.3 Determination of through-dry state . 5
8.4 Determination of through-dry time . 5
8.5 Thickness of coating . 6
9 Precision. 6
10 Test report . 6
Bibliography . 7

© ISO 2009 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 9117-1:2009
ISO 9117-1:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9117-1 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 9,
General test methods for paints and varnishes, in collaboration with CEN/TC 139, Paints and varnishes.
It cancels and replaces ISO 9117:1990, which has been technically revised. The main changes are:
a) failure is defined in terms of damage, rather than damage or marking;
b) the former Annex A concerning required supplementary information has been integrated in the test report.
ISO 9117 c
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27