SIST EN ISO 11643:2009

Leather - Tests for colour fastness - Colour fastness of small samples to solvents (ISO 11643:2009)

SIST EN ISO 11643:2009

Name:SIST EN ISO 11643:2009   Standard name:Leather - Tests for colour fastness - Colour fastness of small samples to solvents (ISO 11643:2009)
Standard number:SIST EN ISO 11643:2009   language:English language
Release Date:13-Jul-2009   technical committee:IUSN - Leather
Drafting committee:   ICS number:59.140.30 - Leather and furs
SLOVENSKI STANDARD
SIST EN ISO 11643:2009
01-september-2009
1DGRPHãþD
SIST EN ISO 11643:2000
Usnje - Preskušanje obstojnosti barve - Obstojnost barve majhnih vzorcev proti
topilu (ISO 11643:2009)
Leather - Tests for colour fastness - Colour fastness of small samples to solvents (ISO
11643:2009)
Leder - Farbechtheitsprüfungen - Farbechtheit kleiner Proben gegenüber Lösemitteln
(ISO 11643:2009)
Cuir - Essais de solidité des teintures - Solidité des teintures de petits échantillons aux
solvants (ISO 11643:2009)
Ta slovenski standard je istoveten z: EN ISO 11643:2009
ICS:
59.140.30 Usnje in krzno Leather and furs
SIST EN ISO 11643:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11643:2009

---------------------- Page: 2 ----------------------

SIST EN ISO 11643:2009
EUROPEAN STANDARD
EN ISO 11643
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2009
ICS 59.140.30 Supersedes EN ISO 11643:1998
English Version
Leather - Tests for colour fastness - Colour fastness of small
samples to solvents (ISO 11643:2009)
Cuir - Essais de solidité des teintures - Solidité des Leder - Farbechtheitsprüfungen - Farbechtheit kleiner
teintures de petits échantillons aux solvants (ISO Proben gegenüber Lösemitteln (ISO 11643:2008)
11643:2009)
This European Standard was approved by CEN on 6 May 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11643:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11643:2009
EN ISO 11643:2009 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 11643:2009
EN ISO 11643:2009 (E)
Foreword
This document (EN ISO 11643:2009) has been prepared by Technical Committee CEN/TC 289 “Leather”, the
secretariat of which is held by UNI, in collaboration with Technical Committee ISO/TC IULTCS "International
Union of Leather Technologists and Chemists Societies".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2009, and conflicting national standards shall be withdrawn
at the latest by November 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11643:1998.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 11643:2009

---------------------- Page: 6 ----------------------

SIST EN ISO 11643:2009

INTERNATIONAL ISO
STANDARD 11643
IULTCS/IUF
434
Second edition
2009-05-15


Leather — Tests for colour fastness —
Colour fastness of small samples to
solvents
Cuir — Essais de solidité des teintures — Solidité des teintures de
petits échantillons aux solvants




Reference number
ISO 11643:2009(E)
IULTCS/IUF 434:2009(E)
©
ISO 2009

---------------------- Page: 7 ----------------------

SIST EN ISO 11643:2009
ISO 11643:2009(E)
IULTCS/IUF 434:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 11643:2009
ISO 11643:2009(E)
IULTCS/IUF 434:2009(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Principle.1
4 Apparatus and materials.2
5 Test specimen.2
6 Procedure .3
7 Test report .4
Annex A (informative) Preparation of dry-cleaning solution containing a detergent .5
Annex B (informative) Commercial sources for apparatus and materials .6

© ISO 2009 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 11643:2009
ISO 11643:2009(E)
IULTCS/IUF 434:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11643/IUF 434 was prepared by the European Committee for Standardization (CEN) Technical
Committee CEN/TC 289, Leather, in collaboration with the Fastness Tests Commission of the International
Union of Leather Technologists and Chemists Societies (IUF Commision, IULTCS), in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement). It is based on IUF 434
published in J. Soc. Leather Tech. Chem., 75, pp. 30-32, 1991, and was declared an official method of the
IULTCS in September 1991.
IULTCS, originally formed in 1897, is a world-wide organization of professional leather societies to further the
advancement of leather science and technology. IULTCS has three Commissions, which are responsible for
establishing international methods for the sampling and testing of leather. ISO recognizes IULTCS as an
international standardizing body for the preparation of test methods for leather.
This second edition cancels and replaces the first edition (ISO 11643:1993), which has been technically
revised. The change in the title, from Leather — Tests for colour fastness — Colour fastness of small samples
to dry-cleaning solutions to Leather — Tests for colour fastness — Colour fastness of small samples to
solvents, reflects the changes in the technology of dry cleaning from solvent-based to water-based processes.
This edition includes an option to use a petroleum hydrocarbon solvent.

iv © ISO 2009 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 11643:2009
ISO 11643:2009(E)
IULTCS/IUF 434:2009(E)
Introduction
The testing of leather to determine its colour fastness to solvents can be done in several ways to achieve
different aims. Small leather samples can be tested to assess the fastness to solvents of leather dyes and
finishes, or of the finished leather itself.
The test method specified in this International Standard covers only the testing of small leather samples, in the
absence of any
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27