|
SIST EN ISO 9692-2:1999
01-december-1999
1DGRPHãþD
SIST EN 29692:1996
Varjenje in sorodni postopki - Priprava zvarnih robov - 2. del: Varjenje jekel pod
praškom (ISO 9692-2:1998)
Welding and allied processes - Joint preparation - Part 2: Submerged arc welding of
steels (ISO 9692-2:1998)
Schweißen und verwandte Verfahren - Schweißnahtvorbereitung - Teil 2:
Unterpulverschweißen von Stahl (ISO 9692-2:1998)
Soudage et techniques connexes - Préparation de joints - Partie 2: Soudage a l'arc sous
flux en poudre des aciers (ISO 9692-2:1998)
Ta slovenski standard je istoveten z: EN ISO 9692-2:1998
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
77.080.20 Jekla Steels
SIST EN ISO 9692-2:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 9692-2:1999
---------------------- Page: 2 ----------------------
SIST EN ISO 9692-2:1999
---------------------- Page: 3 ----------------------
SIST EN ISO 9692-2:1999
---------------------- Page: 4 ----------------------
SIST EN ISO 9692-2:1999
INTERNATIONAL IS0
STANDARD 9692-2
First edition
1998-04-01
Welding and allied processes - Joint
preparation -
Part 2:
Submerged arc welding of steels
Soudage et techniques connexes - Preparation de joints -
Partie 2: Soudage a l'arc sous flux en poudre des aciers
Reference number
IS0 9692-211 998(E)
---------------------- Page: 5 ----------------------
SIST EN ISO 9692-2:1999
IS0 9692-2:1998(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 9692-2 was prepared by Technical Committee
ISOflC 44, Welding and allied processes, Subcommittee SC 7,
Representation and terms.
IS0 9692 consists of the following parts, under the general title Welding
and allied processes - Joint preparation.
- Part 1: Metal arc welding of steel with covered electrode (currently
IS0 9692: 1992)
- Part 2: Submerged arc welding of steels
- Part 3: Manual welding of aluminium and its alloys
O IS0 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 CH-121 1 Genève 20 Switzerland
Internet: central @iso.ch
X.400: c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii
---------------------- Page: 6 ----------------------
SIST EN ISO 9692-2:1999
0 IS0 IS0 9692-2:1998(E)
Introduction
The intention of this International Standard is to use it as an addition to
IS0 9692:1992 (which is to become IS0 9692-1, see Foreword) Metal-arc
welding with covered electrode, gas-shielded metal-arc welding and gas
welding - Joint preparations for steel. It follows similar rules and the same
layout. Therefore, the introduction given in IS0 9692 also applies.
...
Ill
---------------------- Page: 7 ----------------------
SIST EN ISO 9692-2:1999
---------------------- Page: 8 ----------------------
SIST EN ISO 9692-2:1999
INTERNATIONAL STANDARD 0 IS0 IS0 9692-2: 1998( E)
Welding and allied processes - Joint preparation -
Part 2:
Submerged arc welding of steels
1 Scope
This part of IS0 9692 applies to types of joint preparation for submerged arc welding with one wire electrode
(process 121 according to IS0 4063) on steel.
This part of IS0 9692 covers only the welding positions PA and PB according to IS0 6947. In case PC is used, special
preparation will be necessary.
It applies to fully penetrated welds. For partly penetrated welds, types of joint preparation, shapes and dimensions
may differ from the listed proposals if they are specified in the relevant application standard or agreed by parties
concerned.
If the root is welded by a different arc welding process (see IS0 40631, the joint preparation according to IS0 9692
should be taken into account.
2 Normative references
The following standards contain provisions whic
...